Rifles

Kriss Vector Gen 2 10mm 10/33 Magblock 10 & 15 Round Limiter

- This block will convert 33 round Kriss Vector Extended Magazine 10mm magazines into a 10 round magazine.

- Easy to install without damage to your magazines. Block installs into the follower, like other Glock blocks, and stays in place with spring tension.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield - Checkmate M14/M1A 5 Round Limiter For 10 Round Magazine For Hunting

- Easiest and quickest way to make a 10 round M14 - M1A magazine into a 5 round magazine for hunting.

- Can be permanently attached to the spring with epoxy.

- The block attaches to the spring to prevent noise and movement.

- No magazine modifications required.

-Allows loading on a closed bolt with 5 rounds installed.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Century Arms AP51 and AP53 Translucent Polymer Magblock 

- For use in the Century Arms AP51 and AP53 Translucent Polymer 20 round magazines (Like in the Photos)

- These blocks will convert a 20 round Century Arms AP51 and AP53 Translucent Polymer magazine to hold only 10 or 15 rounds.

- NOTE: For use only in Century Arms AP51, AP53 Translucent Polymer manufactured magazines. You will use the factory retaining plate with this block to work.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Century Arms MKE HK 93, 53 and 33 Translucent Polymer Magblock 

- For use in the Century Arms MKE HK 93, 53 and 33 Translucent Polymer 30 round magazines (Like in the Photos)

- These blocks will convert a 30 round Century Arms MKE HK 93, 53, 33 Translucent Polymer magazine to hold only 10 or 15 rounds.

- NOTE: For use only in Century Arms MKE HK Translucent Polymer manufactured magazines. You will not use the factory retaining plate with this block to work this block will replace the factory retaining plate.

-Note: You will have to pull the end of the spring out just a little bit to allow for the block to be inserted into the spring. This can be done with a pair of pliers or a screwdriver.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Bulgarian Tanker AK47 10 and 15 Round Magblock

This block fits the Bulgarian Tanker 20 round AK47 magazines and will convert them to a 10 or 15 round magazine.

-Replaces the lower locking plate.

-Works on Bulgarian Polymer Tanker 20 round magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magazineblock "RESIST" Trucker Snap-Back Hat

- Snap-Back design perfect for all head sizes

- Trucker style is perfect for spring, summer and fall time wheather

- Great to show off your "Resist" pride 

- Offering in Black with red logo and FDE base with OD green front

Magblock Limiter for Russian PPSh-41 35 Round Magazines (7.62x25 Tokarev)

- Fits Russian PPSh-41 35 round magazines chambered in 7.62x25 Tokarev.

- Easy installation under the follower and stays in place with spring tension - Limits the magazine to 10 or 15 rounds of 7.62 Tokarev.

- Held in place with spring tension or can be epoxied for a permanent modification. 

- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

*To ensure proper Fitment of our block, your magazine should look like the one in the pictures.

AMEND2 SCAR 17 MAGBLOCK  

- New and Improved Easy Install Design.

- This block will fit the Amend2 (Only) 7.62x51mm NATO/.308 for the SCAR 17 Magazines made by Amend2.

- The block installs at the bottom of the magazine spring and will convert 20 round magazines to hold only 10 rounds.

- No modifications to your Amend2 SCAR 17 polymer magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

- This block is designed and tested for the Amend2 SCAR 17 magazine only and won't work in factory FN SCAR 17 magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 & 15 Round Limiter Overwatch Precision Mod2 MP5 9mm 32 Round Magazines

- Fits 32 round 9mm Overwatch Precision Mod2 MP5 style magazines.
- Limits the magazine to 10 or 15 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

NOTE: This block is designed for the Overwatch Preceision Mod2 Magazines MP5 Magazines Only.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.
 

USGI Duramag, C-Products 7.62x39 AR-15 Magblock 5/10 (2 and 5 Round Magazine Capacity Limiter)

- Fits USGI 10 round magazines made by C-Products/Duramag. 
- This block will attach to the bottom of the spring.
- Will convert a 10 round (7.362x39) magazine to hold only 5 or 2 rounds.
- Magazines can be loaded with the bolt closed in most rifles. Fitting may be required in some cases.
- Does not affect reliability.
- No increase in spring pressure. 
-Installs at the base of the magazine.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

SDS Imports AR-15 Polymer 10/30 Magblock 

- For use in the SDS Imports AR-15 Polymer 30 round magazines (Like in the Photos)

- These blocks will convert a 30 round SDS Imports AR-15 Polymer magazine to hold only 10 or 15 rounds.

- NOTE: For use only in SDS Imports AR-15 Polymer manufactured factory magazines. You will use the factory retaining plate with this block to work.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Heckler & Koch UMP 10mm/40 Magblock

- Works with H&K UMP 10mm - 40S&W 30rd Magazines as shown.

- 10 and 15 round options available below. Also a 5 round options for hunting

- This block will replace the factory locking plate

- Simple quick installation.

- With our block it allows for the full power of the spring to be used.

-This block has only been tested in the German made UMP 10mm - .40 magazines.

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

SIG SAUER MCX-SPEAR 6.8X51, 7.62x51, 6.5 CREED, 277 FURY Magblock Limiter

- This block will convert a 20 round magazine to hold only 10 rounds.
- Only fits the "New" Sig Sauer made MCX-Spear 6.8x51mm, 7.62 nato, 277 Fury 20-round magazines.
- Does not affect reliability.
- No increase in spring pressure or wear. 

Note: This is a custom modified Pmag block and allows for use of the factory locking plate. This block will not work in the Lancer MCX-Spear 20-round magazines. If you need a magblock for the Lancer MCX-Spear 20-round magazine check in the related products under this posting.

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

SPRINGFIELD SAINT VICTOR 10 & 15 ROUND LIMITER (9MM)

This block will work with 32 round 9mm Springfield Saint Victor magazine made by Metalform to make a 10 or 15 round magazine.

It replaces the lower floor plate.

The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.