Rifles
-
Thermold 10/30 Magblock
Magblock 10/30 MCL (Magazine Capacity Limiter) for Thermold 30 round AR-15/M16 Magazines.
- Fits Thermold 30 round black Zytel Nylon magazines in 5.56 mm, 223 Cal.
- Will convert a 30 round magazine to hold 10 rounds.
- Only fits current production Thermold magazines.- No modification of the original magazine is needed.$6.50 As low as: $5.95 -
AR-10 ArmaLite Magblock (10 or 15 Round Limiter)
Magblock for ArmaLite AR10 20 Round Magazines. 10 and 15 Round Limiters.
Fits ArmaLite AR10 .308/7.62x51mm 20 round magazines and will convert them to hold either 10 or 15 rounds.
- Easy to install in seconds.
- No need to drill any holes.
- Load magazines on a closed bolt in most rifles.
- No external magazine modifications required.New lighter, more reliable design is made from abs plastic.
$6.95 As low as: $5.95 -
STEN 10/32 Magblock 10 Round Limiter
Magblock 10 Round Limiter for Sten 32 and 20 Round Magazines
- Fits Sten 32 round magazines and 32 round magazines that have been "Brass Wire" limited to 20 rounds. You must choose an option below.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Please Note: The Photos show a 32 round magazine that has 2 brass wires on the inside that protrude outside near the bottom of the magazine. This is a Sten 32 round magazines that was limited to a single stack 20 round magazine. This was a common military modification that helped with reliability and very widespread on surplus magazines. Please select the "Single Stack Modified" option below if you see these brass wires at the bottom of your magazine to ensure you receive the proper limiter. Thank you.$6.95 As low as: $5.95 -
CAA 15/30 Magblock 15 Round Limiter
15 Round Limiter for CAA Indicative 30 Round Polymer Magazines
Magblock 15/30 MCL (Magazine Capacity Limiter) for CAA 30 round polymer magazines in .223/5.56mm.
- This block will attach to the bottom of the spring, and sits on top of the original locking plate.
- Easy conversion of 30 round CAA magazines to hold 15 rounds.
- Does not affect reliability.
- No increase in spring pressure.$6.25 As low as: $5.25 -
Pmag LR 20 Magblock 10/20 Gen M3 (.308)
Pmag LR20 Magblock GEN M3 Magazine Capacity Limiters (5, 10, and 15 Round Limiters Available)
Fits the Magpul LR20 .308/7.62x51mm Pmags and will convert them to hold only 5, 10, or 15 rounds. Select desired size below. Easy to install.
- Will NOT fit older version magazines. Gen M3 Only.
- Dust covers still fit with 10 rounds loaded.
- Load magazines on a closed bolt in most rifles.
- Easy to install.
- No external magazine modifications.
-This block requires you use the factory Magpul locking plate with our block (See picture 1 and 2).
$6.50 As low as: $5.95 -
VEPR .308 Magblock 5, 10, and 15 Round Limiters
Magblock for Vepr .308 20 Round Magazines. 5, 10 and 15 Round Limiters.
Fits Vepr .308/7.62x51mm 20 round magazines made by Csspecs>
- Easy to install in seconds.
- Tested in Vepr magazines made by Csspecs. May fit other manufacturers with or without modification.
- Replaces the original locking plate.
- No external magazine modifications.
- Select 5, 10 or 15 round limiter below.$6.95 As low as: $5.95 -
FAL 10/30 Magblock
Converts FAL 30 round magazines to 10 rounds.
This block will fit FAL 30 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.Tested in DSARMS manufactured 30 round magazines, but should work in other similar magazines.
$6.59 As low as: $4.95 -
Pmag 6.8 mm Six8 10/30 Magblock 10 Round Limiter
Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round 6.8 mm "Six8" Pmags for LWRC.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Includes a spacer for the proper height in the 6.8 mm magazine.
- Does not affect reliability.
- No increase in spring pressure.
- *Compatible with Pmag 6.8 mm Magazines Only
$6.95 As low as: $5.25 -
H&K HK416, MR556, SA80 Magblock 10/30 (5.56)
H&K Magblock 10/30 Limiter
- For use in H&K SA80 and HK416 type 30 round magazines as pictured.
- These blocks will convert a 30 round magazine to hold only 10 rounds.
- The locking plate is not used with the limiter installed.
$6.50 As low as: $5.95 -
UZI and Metalform 30/32 Magblock
This block will work with 32 round 9 mm UZI and MetalForm magazines to make a 30 round magazine. It replaces the lower floor plate. The spring can also be epoxied to the block which allows for disassembly and cleaning, or epoxy the floor plate closed for a more secure modification.$6.95 As low as: $5.95 -
5.45x39 AR15 Magblock 10/30 Limiter
Magblock 10/30 limiter for 5.45x39 mm AR Magazines only.
- Tested in C-Products and ACS magazines.
- These blocks will convert a 30 round 5.45x39 mm magazine to hold only 10 rounds.
$5.95 As low as: $4.50 -
Steyr AUG 10/30 Magblock (10 & 15 Round Limiter)
10 Round Limiter for Steyr AUG 30 Round Polymer Magazines
Magblock 10/30 MCL (Magazine Capacity Limiter) for Steyr AUG 30 round polymer magazines in .223/5.56mm.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Customized base of the Magblock includes two locking points just like the original locking plate.
- Does not affect reliability.
- No increase in spring pressure.
$6.95 As low as: $6.50 -
SCAR 16 Magblock 10/30 Limiter
SCAR 16 Magblock 10/30
- For use in the SCAR 16 FNH 30 round magazines
- These blocks will convert a 30 round SCAR 16 magazine to hold only 10 rounds.
- No modification to your original SCAR magazines is required to use these limiters.
- NOTE: For use only in FNH manufactured SCAR 16 factory magazines. For regular metal AR magazines you must use the USGI limiters.
$6.95 As low as: $5.95 -
Masterpiece Arms MPA 10/32 Magblock 9mm (Tapco)
10 Round Limiter for 32 Round Tapco MPA Magazines
Magblock 10/32 Magazine Capacity Limiter for the Masterpiece Arms 32 round 9mm magazines made by Tapco.
- This block will replace the lower spring attachment point or locking plate and convert a 32 round magazine to hold only 10 rounds.
- Very easy to install
- Does not affect reliability.
- No increase in spring pressure.
- Slight modification of the follower is required to fit all 10 rounds. Please see the pictures posted here for instructions.
$6.95 As low as: $5.95 -
Vepr 7.62x39 mm 10/30 Magblock
Vepr 7.62 x 39 mm 10/30 Magblock- for SMG Tactical / Surefire Magazines
- Converts the Vepr polymer 7.62 x 39 mm 30 round magazine made by SMG Tactical to 10 rounds.
- This block fits the 30 round Vepr SMG (Surefire Gun Mags) or Surefire Magazines. (May fit others, but not tested at this time)
- This block will replace the original magazine locking plate.
- Also fits the Saiga 30 round 7.62x39 magazines made by SMG.
$7.49 As low as: $5.95