Rifles

Magblock 10/20 MCL (Magazine Capacity Limiter) for Magpul 20 round Gen M3 Pmags in .223/5.56mm, 300 Blackout

- Fits NEW Gen M3 Pmag 20  (Curved body)

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed in most rifles. Some trimming of the limiter may be required for this.

- Does not affect reliability.

- No increase in spring pressure. 

- Attention: We now offer the option to use our block with the Magpul factory retaining plate with our block. The block will sit on top of the Magpul retaining plate and is cut differently than our standard Gen M3 10/30 magblock. If you're planning on not using the factory retaining plate then we have an options for you.

Saiga 7.62 x 39 mm 10/30 Magblock

- Converts the Saiga polymer 7.62 x 39 mm 30 round magazine to 10 rounds.

- This block fits the 30 round Saiga SMG (Surefire Gun Mags) or Surefire Magazines. (May fit others, but not tested at this time)

- This block will replace the original magazine locking plate.

Heckler & Koch G36 Magblock

- Works with Magpul Pmag Magazines for the HK G36 only.

- 10/30 configuration (10 rounds in a 30 round body)

- Replaces the original locking plate

- Simple quick install. 

Suomi Magblock Limiter for 36 Round Magazine 

- New design does not replace the difficult to remove lower floor plate but instead rests on top of it.

- The spring can also be epoxied to the block which allows for disassembly and cleaning.

- Easy and simple way to make 10/36 Suomi magazines without damaging your hard to find magazine. 

- These are made of heavy-duty ABS and are meant to work for the life of the magazine.

Arsenal Bulgarian Circle 10 AK-47 Magblock

-This block fits the Arsenal 30 round AK47 magazines and will convert them to a 10 round magazine

-This block will also work on the smoothside Bulgarian 30-round AK-47 magazines pictured

-Replaces the lower locking plate

-Works on Arsenal Bulgarian 7.62x39mm AK magazines

Note: This block is made from our Universal AK Kits cut to #38 using a square locking plate

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

• Converts 9mm AR-15 32 round magazine to 10 rounds.
• This block will work with 9mm AR-15 magazines made by ProMag only.
• It replaces the lower floor plate. 
• The spring can also be epoxied to the block which allows for disassembly and cleaning. 
• We have a separate block available for UZI, C-Products, and ASC 32 round magazines. This one only fits Promag magazines.

Troy BattleMag 10/30 MCL (Magazine Capacity Limiter) for 30 round Troy BattleMags in .223/5.56mm.

- This block will sit on top of the Troy locking plate and convert a 30 round magazine to hold only 10 rounds.

- The optional shock absorbing floor plate will still function normally.

- Does not affect reliability.

- No increase in spring pressure or wear. 

(Note: This is a custom trimmed Pmag block)

Lancer L5 10/30 MCL (Magazine Capacity Limiter) for 30 round Lancer L5 Advanced WarFighter magazines in .223/5.56mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- Only fits L5 Advanced Warfighter with slide on base. Will not fit older L5 magazines.

- Does not affect reliability.

- No increase in spring pressure or wear. 

(Note: This is a custom modified Pmag block)

-This block will also work in the 30-round 300 Blackout Lancer magazines along with the new Gen 2 Warfighter magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Lancer L5 10/20 MCL (Magazine Capacity Limiter) for 20 round Advanced Warfighter L5 magazines in .223/5.56mm.

- This new design block will sit on top of the lower spring attachment point or locking plate and convert a 20 round magazine to hold only 10 rounds.—

- Only fits L5 Advanced Warfighter with slide on base. Will not fit older L5 magazines.

- Does not affect reliability.

- No increase in spring pressure or wear. 

- Uses a custom modified Pmag Block. 

-This block will work in the New Gen2 Lancer Magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 15/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in .223/5.56mm. (Gen 2)

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 15 rounds.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure. 

- Will also fit 30 round Emags.

Note: This is a trimmed down 10 round block to allow 15 rounds.  These will not work in Gen M3 Pmags. Gen M3 Pmag 15 round limiters are available as a different product. These fit Gen 2 Pmags only.  

Magblock 15/20 MCL (Magazine Capacity Limiter) for Magpul 20 round Pmags in .223/5.56mm. (Gen 2 only)

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 15 rounds.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure. 

Note: This is a trimmed down 10 round block to allow 15 rounds.  These fit Straight Body Gen 2 Pmags only.  Gen 3 limiters are available as a different product. 

10 Round Limiter for Gen M3 30 Round Pmags

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Gen M3 Pmags in .223/5.56mm. 

• This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.
• The Pmag dust covers will still fit when loaded.
• Magazines can be loaded with the bolt closed.
• Does not affect reliability.
• No increase in spring pressure. 
• This block will work in the New Magpul TMAG Gen M3 30-round magazines.
• Attention: We now offer the option to use our block with the Magpul factory retaining plate with our block. The block will sit on top of the Magpul retaining plate and is cut differently than our standard Gen M3 10/30 magblock. If you're planning on not using the factory retaining plate then we have an options for you.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

10 Round Limiter for 30 Round THRIL PMX Magazines

Magblock 10/30 MCL (Magazine Capacity Limiter) for THRIL PMX 30 round in .223/5.56mm. 

- This block will allow you to use the factory locking plate and convert a 30 round magazine to hold only 10 rounds.

- Does not affect reliability.

- No increase in spring pressure. 

Magblock for X-Tech Tactical AK47 (7.62x39mm) Magazines.

- This block fits the XTECH Tactical 30 round AK47 magazines in 7.62x39mm and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

Want to upgrade to the best stainless steel AK replacement springs available? See our upgrade springs here: LINK