Sig Sauer

Sig Sauer P226 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Sig P226 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/15 Sig Sauer P226 magazines. 
- No modification to the magazine is required.
-  Lightweight and will not interfere with magazine reliability.
- Tested on factory Sig P226 magazines as shown in the photos. The block may need to be modified to work with magazines from other manufactures. 

*This magazine is known to use two different types of followers depending on where they were manufactured. Please select the country of manufacture or your follower length below. The most accurate way is to measure your follower as shown in the photos. 

Magblock 10 Round Limiter for Sig 15 Round P229-1 Magazines. 
Fits the Sig P228 M11-A1

- Fits the new 15 round 9mm Factory Sig P229-1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Taran Tactical +1 Extension for Sig Sauer P320 10/18 (9mm) Magblock

- Fits 17 round 9mm Sig P320 with the TTI (Taran Tactical Innovations) +1 Magazine Extension.  *See Pictures For Details
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block is designed to work with the +1 TTI Extension for the Sig P320 Full-size 17-round magaiznes.

Mag Magnet for AR15

ALL NEW and Improved Generation 2 model, using the N52 Neodymium Magnet for strongest hold with 1.3 lb more strength than the original. 
Mag Magnet is a patented product that is magnetized and used with the standard bullet button for California legal AR-15's. Mag Magnet is a true original, don't fall for cheap imitations.

For use with the standard AR-15 platform (.223/5.56mm).
Mag Magnet is not compatible with the Prince 50 or the Raddlock. It only works with the standard Bullet Button™.

Magblock LLC only recommends use of this device out of state or with .22 rimfire conversion kits only.

Leaving Mag-Magnet on a firearm may designate it as an illegal assault weapon in violation of California law. Do not use Mag-Magnet in California on magazines with capacities greater than 10 rounds. It is advised that Mag-Magnet users become familiar with California DOJ requirements and updated interpretations of existing laws and regulations.

Magblock LLC shall not be held responsible in any way for the inappropriate use of the product by the user. User assumes all liabilities and risks associated with ownership and use of this product.

Magblock 10 Round Limiter for Sig P320 (.40) 13 Round Magazines

- Fits 13 round .40 Sig P320 factory magazines.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
  *** *Compatibility Note: This is the same block as a Sig P228 9mm 10/13 Limiter and may be marked as such***

Magblock 10 Round Limiter for Sig MPX 9mm 30 Round Magazines

- Fits 30 round 9mm Sig MPX factory magazines.
- Easy installation.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. (Follower insert requires epoxy or silicone to securely hold in place).
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
 

ATTENTION: This block will not work on the new Sig MPX magazines. See picture #2 for an example of the new style Sig MPX magazine.

Magblock Universal Pistol Limiter kit allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

Sig Sauer X-Five, P320 and P250 Magblock 10 round limiter for 21 round magazines.

This Magblock fits the Sig X-Five, P320 and P250 21 round 9 mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/21 Sig Sauer X-Five, P320 and P250 magazines. 

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Tested on factory Sig X-Five, P320 and P250 21 round magazines. The block may need to be modified to work with magazines from other manufactures.

- This is also the same product as the P320 and P250 limiter for 21 round magazines.

-NOTE: Universal Limiter Instructions: Use at maximum length with 25 showing in the indicator notch. Use the locking tab, but cut off the lock button for a flat base. Cement Together.

Attention: This block is designed for the 21rd magazine only.

Magblock Universal Pistol Limiter 3 Pack Kit
Allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

Magblock 10 Round Limiter for Sig P229 and P226  12 Round .40 Magazines. 

- Fits the new 12 round .40 Factory Sig P229 and P226 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P226 ,12 Round .40 Magazines. 

- Fits the new 12 round .40 Factory Sig P226 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
- Uses the Universal Limiter cut with #6 in the indicator notch with a flush base.

Magblock 10 Round Limiter for Sig P365 and P365X, 365XL 12 Round Magazines

- Fits 12 round 9mm Factory Sig P365, P365X and P365XL magazines. 
- Save time and money with a simple install.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification where required to be legal. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P229 and P226  12 Round .40 Magazines. 

- Fits the new 12 round .40 Factory Sig P229 and P226 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
-*Same as CZ 10/12 limiter and likely marked as "CZ".

Magblock 10 Round Limiter for Sig P226 (.40) 13 Round Magazines

- Fits 13 round .40 Sig P226 magazines made by Mec-Gar. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
  *Universal Limiter can be used to make this block. Cut the base flush with #8 showing in the indicator notch.