FN 509 Tactical Magblock 10 Round Limiter for the 24 round magazine

- Fits 24 round 9 mm Factory FN 509 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

FN Five-Seven Magblock 10 Round Limiter

- Fits 20 round 5.7 mm Factory FN magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

NOTE: May need to be trimmed a little shorter for proper function with 10 rounds loaded and the slide closed in some pistols.

Now offering a 5 round limiter for those who plan to use this for hunting.

* This block will work in standard FN 5.7 and FN 5.7 MK3 magazines.

FNS-9 and FNS-9 Compactg Magblock 10 and 15 Round Limiters

- Fits 17 round 9 mm Factory FNS-9 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 or 15 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

FNX-45 Magblock 10 Round Limiters

- Fits 15 round .45 Factory FNX-45 magazines.
- Must check follower type to determine the correct limiter. 
- Limits the magazine to 10 rounds of .45
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

*Please check your follower and see the photo to determine the correct limiter needed. One type installs under the follower at the top of the magazine. If the follower has a plastic part protruding downward then you need the follower that installs at the bottom of the magazine. 

Epoxy Fast Setting

Hardman Double Bubble Pouch (4.0 grams). Will work for a few rifle or up to 5-10 pistol limiters depending on amount used.
Features:
- Starts to set in only 3- 5 minutes. Mix small batches if doing a lot of limiters.
- Handling strength: 15-30 minutes.
- Color: white.
- Viscosity: honey.
- Full Strength: 24 hours

4.0 Grams.

Epoxy, Machinable Fast Setting.

Hardman Double Bubble Pouch (3.5 grams). Will work for a few rifle or up to 10 pistol limiters depending on amount used.
Features a longer working time than the Red fast set epoxy:
- Starts to set in 25 minutes, Handling time 4 hours. Mix small batches if doing a lot of limiters.
- Handling strength: 4 hours.
- Color: Aluminum.
- Viscosity: Honey.
- Full Strength: 24 hours

3.5 Grams.

Magblock Universal Pistol Limiter kit allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

FNX and FNP .40 Magblock 10 Round Limiter

This Magblock fits the FNX and FNP .40 14 round magazines and will limit them to 10 rounds.  Easily installed in seconds under the follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10 round FNX and FNP .40 Magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

FNP-45 Magblock 10 Round Limiters

- Fits 15 round .45 Factory FNP-45 magazines. 
- Easy installation under the follower. Save time and money!
- Limits the magazine to 10 rounds of .45 and retains normal function.
- Held in place with spring tension or can be epoxied for a permanent modification where required by law.
- Lightweight, efficient design. 

 

FNS-40 and FNX-40 Magblock 10 Round Limiter for 14 Round Magazines (.40)

- Fits 14 round FNX-40 and FNS-40 Factory magazines. 
- Save time and money with this simple part. 
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

FYI: The Universal limiter can also be used to make this block. Cut the universal limiter so that between #11 and #12 show in the indicator notch. 

FN 509 Magblock 10 and 15 Round Limiters

- Fits 17 round 9 mm Factory FN 509 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 or 15* rounds of 9 mm.
    *Must select below for 15 round or will be shipped as a 10 round limiter
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

FNS-9 Magblock 10 Round Limiter

- Fits 16 round 9 mm Factory FNP-9 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

FNS-9 Compact Magblock 10 Round Limiters

- Fits 12 round 9 mm Factory FNS-9 compact magazines. 
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

FN 509 Magblock 10 Round Limiter For 15 Round Magazines

- Fits 15 round 9 mm Factory FN 509 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.