Beretta

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture. 

Beretta M9A3 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta M9A3 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta M9A3 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta M9A3 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

Magblock Universal Pistol Limiter 3 Pack Kit
Allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

Beretta APX Magblock 10/15 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 15 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #9 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #9 will show in the limiter window notch like in the photos. 

Beretta 96FS MecGar Magblock 10/13 (.40) 10 Round Limiter

This Magblock fits the MecGar Beretta 96FS 13 round magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 96FS magazines.
- Save time and money and keep your magazines legal. 
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" MecGar 96 magazines as seen in the photos.

*If using our Universal Limiter for this magazine: Cut to #8 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. #4 will show in the limiter window notch like in the photos. 

Beretta 81 Magblock 10/12 (.32) 10 Round Limiter

This Magblock fits the factory Beretta 81, 81B, 81BB 12 round .32 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/12 Beretta 81 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 81 magazines as shown in the photos. Other types of magazines may require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to "7" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Beretta PX4 Full Size Tactical Magblock 10/17 (.40) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round .40 caliber magazines and will limit them to 10 rounds. Installs at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired. (This block is for the tactical version magazine).

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines in .40S&W.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 (.40) magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #19 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Beretta 92 Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 15 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 92 magazines as seen in the photos.

*** If you have M9 magazines made by Mec-Gar you must select the option below for a longer limiter. These magazines are marked "M9" on the side. 

NOTE: Multiple variations of this magazine may exist. Consider ordering the "Do not glue" option below.  Another option is the Universal Kit below which you can start with the block cut to around 12 and test the fit. Most need to be cut around 10, but the Universal Limiter gives you the option to custom fit to your magazine and tension on the last round. Order the Universal at this link:  http://www.magazineblocks.com/magento/magblock-universal-pistol-limiter.html

*If using our Universal Limiter for this magazine: Cut to #9-10 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #9-10 will show in the limiter window notch like in the photos.  The M9 magazine uses the universal limiter cut to #15.

Magblock Universal Pistol Limiter kit allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

Beretta PX4 Full Size Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 15 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/15 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 15 round Beretta PX4 magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #17 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Beretta PX4 Compact Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Compact Beretta PX4 15 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/15 Beretta Compact PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 15 round Beretta PX4 magazines and CX4 as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #12 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Beretta 92 Compact Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 Compact 13 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 92 Compact magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 92 magazines as seen in the photos.

*If using our Universal Limiter for this magazine: Cut to #5 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. #5 will show in the limiter window notch like in the photos. 

Beretta 96 Magblock 10/12 (.40) 10 Round Limiter

This Magblock fits the factory Beretta 96 12 round magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/12 Beretta 96 magazines.
- Save time and money and keep your magazines legal. 
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 96 magazines as seen in the photos.

*If using our Universal Limiter for this magazine: Cut to #4 and glue flush at the bottom for 10/12 limiter. Slide lock is not used. When epoxy cures assemble magazine. #4 will show in the limiter window notch like in the photos. 

Beretta 92 Mec-Gar Magblock 10/18 (9mm) 10 Round Limiter

This Magblock fits the Mec-Gar Beretta 92 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on Mec-Gar (M9) Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #15 and glue flush at the bottom for 10/18 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #15 will show in the limiter window notch like in the photos.