Pistols

Armscor/RIA XT-22 Magnum  (.22WMR) Magblock 10 Round Limiter for 14 Round Magazine.

- Fits 14 round Armscor/Rock Island Armory XT-22 magnum magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22magnum
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Marlin Camp 9 (9mm) 12 Round Magazines

- Fits 12 round 9mm Marlin Camp 9 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. 

Beretta M9A3 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta M9A3 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta M9A3 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta M9A3 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

Zev Technologies Plus 5 Glock 17 and Glock 34 (9mm) Magblock  10/22

- Fits 22 round 9mm Zev Technologies plus 5 basepad extension for Factory Glock 17 and Glock 34 magazines.  *See details on correct follower types below. 

- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

Patent Pending

*This block is intended for the +5 Zev Technologies basepad extensions attached to a factory Glock 17 & Glock 34 magazine, and will limit a 22 round magazinedown to 10 rounds. *See pictures of Zev +5 Extension. 

Tanfoglio Stock Master Magblock 10/17 Round and 15/17 Round Limiter for 17 Round Magazines

This Magblock fits the Tanfoglio Stock Master 9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Tanfoglio Stock Master and  Italia Defiant Stock Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

"Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "18" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

*This block is designed for the Tanfoglio Stock Master Factory magazine (ONLY), and will not work on Mec-Gar magazines. 

Smith & Wesson M&P Shield Plus, Equalizer 9mm Sub-Compact Magblock 10 Round Limiter

- Fits 13 round 9mm M&P Shield Plus magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Taurus G3 Magblock 10/17 and 15/17 (9mm) 10 and 15 Round Limiter

This Magblock fits the factory Taurus G3 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus G3 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture. 

Walther PDP Compact Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Walther PDP Compact magazines as shown.
- Tested in Walther PDP Compact Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit.

-This block will fit the new PDP-F magazines. 

Beretta PX4 Full Size Tactical Magblock 10/17 (.40) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round .40 caliber magazines and will limit them to 10 rounds. Installs at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired. (This block is for the tactical version magazine).

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines in .40S&W.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 (.40) magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #19 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

Springfield XDM Elite Compact 9mm Magblock 10/14

- Fits 14 round 9mm XDM Elite Compact magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Springfield XDM Elite Compact 9mm Magblock

Springfield XD 9mm 10/15 Round Magblock

• Fits 15 round XD and XD Mod 2 9mm magazines. 
• Easy installation at the base of the magazine.
• Limits the magazine to 10 rounds of 9mm.
• Can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

*This block is designed for the factory 15 round magazine, made by Springfield. Will not work on Promag XD magazines.

Taurus TX-22  (.22LR) Magblock 10 Round Limiter for 16 Round Magazine.

- Fits 16 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

ProMag Springfield XDM 9mm Magblock

- Fits 19 round 9mm XDM magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

ProMag Springfield XDM 9mm Magblock