Pistols

Promag FN Five-Seven Magblock 10 Round Limiter

- Fits 30 round 5.7 mm Promag FN magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

ETS Glock 9mm Magblock 10 Round Limiter for 32 round Magazines

This Magblock fits the ETS 32 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/32 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

*This block is designed for the ETS 32 Glock magazines only. If used in other magazines it might need to be modified.

Genuine Factory Beretta 92FS Magblock 10/18 (9mm) 10 & 15 Round Limiter

This Magblock fits the factory Beretta 92FS Series 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta 92 Series magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92FS 18 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

 Attention: Make sure to verify what magazine you have before ordering. This block will fit the following 18-round 92FS series magazines Made By Beretta and not MecGar:

Beretta 90-two, Beretta 92G, Beretta M9, Beretta 92D, Beretta 92 Vertec, Beretta 92F, Beretta 92GTS

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield SA35, SDS Imports L9A1 Hi-Power 9mm 10/15 Round Magblock

• Fits 15 round SA-35 and SDS Imports Hi-Power 9mm magazines. 
• Easy installation at the base of the magazine.
• Limits the magazine to 10 rounds of 9mm.
• Can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

Ruger Security-380 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Ruger Security-380 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired. This block works inconjuntion with the factory spacer from Ruger. Please see pictures for details.

-Simple install to make 10 round Ruger Security .380 Magazines.

-No modification to the magazine is required. The spring bottom can fit into the drilled hole in the limiter or you can bend the spring if desired.

-Lightweight and will not interfere with magazine reliability.

Magblock 10 Round Limiter for Springfield DS 1911 Prodigy 17 Round 9mm Magazines

- Fits 17 round 9mm Factory Springfield Prodigy 1911 DS magazines. 
- Easy installation into the follower (See pictures).
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 Magblock 10 Round Limiter for Heckler & Koch Mk23 .45 

- Save time and money converting your magazines.
- Fits 12 round .45 H&K Mk23 magazines. 
- Limits the magazinbe to 10 rounds of .45
- Easy installation at the base of the magazine. Sits on top of the locking plate as shown.
- Held in place with tension or can be epoxied in place.
- Lightweight, efficient design. 

 Magblock 10 Round Limiter for Heckler & Koch P7M13 9mm

- Fits 13 round 9mm H&K P7M13 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation under the follower as shown in the photos.
- Lightweight, efficient design. 

-This block will work in P7M10 .40S&W marked magazines.

New Magblock 10 Round Limiter for Sig P320-FLUX LEGION 30 Round Magazines

- Fits 30 round 9mm Factory Sig P320 & P320 Flux Legion amagazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Sig MPX 9mm 35 Round Magazines

- Fits 35 round 9mm Sig MPX factory magazines.
- Easy installation by inserting the block at the base. This block replaces the factory locking plate.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

FN 502 (.22LR) Magblock 10 Round Limiter for 15 Round Magazine.

- Fits 15 round FN 502 magazines. 
- Easy installation and allows you to use the stock locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 Magblock 10 Round Limiter for Heckler & Koch P30 and VP9 9mm 15 round magazine that has a +5 HK store extension

- Fits 15 round to 20 round 9mm H&K P30 and VP9 magazines that has the +5 extension.
- Limits the magazine to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

Magblock Limiter for Bul Armory SASII 2011 126mm 19 Round 9mm Magazines

- Fits 19 round 9mm Factory Bul Armory SASII 126mm w/ a +1 extension magazines. 
- Easy installation at the base of the magazine. (See pictures for details)
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

Magblock 10 Round Limiter for Bul Armory SASII 2011 120mm 14 Round 45acp Magazines

- Fits 14 round 45acp Factory Bul Armory SASII 120 mm magazines. 
- Easy installation at the base of the magazine. (See pictures for details)
- Limits the magazine to 10 rounds of 45acp. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.