Pistols

Magblock 10 Round Limiter for Sig P320 (.40) 13 Round Magazines

- Fits 13 round .40 Sig P320 factory magazines.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
  *** *Compatibility Note: This is the same block as a Sig P228 9mm 10/13 Limiter and may be marked as such***

Sig Sauer P320 and P250 Compact Magblock 10 Round Limiter for Factory 15 Round Magazines

This Magblock fits the Sig P320 and P250 Compact 15 round 9 mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/15 Sig Sauer P320 and P250 compact magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Tested on factory Sig P320/P250 compact, XCompact, Xcompct Pro magazines. The block may need to be modified to work with magazines from other manufactures.

Options: See attached photos and video. Sig has changed their locking plate/retaining plate on the Sig P320 15 round magazine recently. They now use a thinner locking plate on the newer magazines. It's important to watch the whole video to determine which size retaining plate you have in your magazine.

Magblock 10 Round Limiter for Sig Sauer P320 Factory 17 Round Magazines

- Fits 17 round 9mm Factory Sig P320 and P250 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant polymer.

-This block will work in the 17rd X-Carry, M18, M17, X-Legion magazines. It will also work in the P250 16-round magazines too.

Smith & Wesson M&P22 (.22LR) Magblock 10 Round Limiter New Improved Fit

- Fits 12 round .22 M&P-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Beretta 92, 92FS, M9A1, Stoeger 8000 Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 15 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta 92, 92FS, M9A1, 92G, 92G Elite LTT II 15-round magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 92 magazines as seen in the photos.

*** If you have M9 / Mec-Gar marked magazines made by Mec-Gar you must select the option below for a longer limiter. These magazines are marked "M9" or just "MecGar" "Made in Italy" on the side or have the dimple in beaded into the magazine. The dimple is easiest to spot.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.