Magblock 10 Round Limiter for Remington RP45 .45 magazines

- Fits 15 round .45 Remingto RP45 and 1911 R1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 & RP45 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Remington RP9 9mm magazines

- Fits 18 round 9mm Remingto RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington RP9 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Remington 1911 R1 9mm magazines

- Fits 18 round 9mm Remingto RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Remington 1911 R1 .40 magazines

- Fits 18 round .40 Remington RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 .40 double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for H&K MP5 9mm 30 Round Magazines

• Fits 30 round 9mm HK MP5 factory magazines.
• Limits the magazine to 10 rounds of 9mm
• Held in place with spring tension or can be epoxied for a permanent modification. (Block installs into the follower and not at the base of the magazine).
• Lightweight, efficient design. 

ATTENTION: This block will not work in the Zenith MP5 style magazines. We have blocks listed for that under Zenith ZF-5
 

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 21 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/21 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

 Wilson Combat EDC X9, SFX9, SFT9, Experior Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Wilson Combact EDC X9 magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Bersa Thunder Ultra Compact Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Bersa Thunder Ultra Compact 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder Ultra Compact 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/13 Bersa Thunder Plus Ultra Compact magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "6" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Bersa Thunder Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Bersa Thunder 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/17 Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "16" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Bersa Thunder Magblock 10/13 (.40) 10 Round Limiter

This Magblock fits the factory Bersa Thunder .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder .40 magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/13 Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "8" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Beretta PX4 Full Size Magblock 10/20 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 20 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. It is held in place with spring tension alone or can be glued or epoxied if desired. 

- Save time and your expensive factory magazines. Quick install to make 10/20 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 20 round Beretta PX4 magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

CZ-75 Tactical Sport 10/17 Magblock 10 Round Limiter for 17 Round factory magazines

This Magblock fits the CZ-75 Tactical Sport 17 round magazines will limit them to 10 rounds. Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/17 CZ-75 magazines.

- No external modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

NOTE: Universal Limiter Instructions: Indicator notch should show "18" which is the maximum length, the base is flush.

ETS Glock .40 Magblock 10 Round Limiter for 30 round Magazines

This Magblock fits the ETS 30 round .40 magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/30 Glock .40 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

ETS Glock 9mm Magblock 10 Round Limiter for 40 round Magazines

This Magblock fits the ETS 40 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/40 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

-This magazine fits all Glock double stack 9mm firearms.