Pistols

Magblock 10 Round Limiter for Marlin Camp 9 (9mm) 12 Round Magazines

- Fits 12 round 9mm Marlin Camp 9 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. 

Armscor/RIA XT-22 Magnum  (.22WMR) Magblock 10 Round Limiter for 14 Round Magazine.

- Fits 14 round Armscor/Rock Island Armory XT-22 magnum magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 magnum
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield Hellcat 9mm 10/15 Magblock

- Fits 15 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Note: Please verify which number is showing under the follower of your magazine. If the number reads #1, #3 or #4 then you'll need a special cut Hellcat block. If it reads any other number, then you can use the standard cut block.

Taurus GX4 Magblock 10/11 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus GX4 11 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus GX4 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

Magblock 10 and 15 Round Limiter for EAA Girsan MC28 17 Round Magazines

- Fits 17 round 9mm EAA Girsan MC28 factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #11.5 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #11 with the top part of #12 will show in the limiter window notch like in the photos.  

Magblock 10 and 15 Round Limiter for Steyr L9-A2 17 Round Magazines

- Fits 17 round 9mm Steyr A2-MF factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #17 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. 

Magblock 10 and 15 Round Limiter for Steyr SPP 30 Round Magazines

- Fits 30 round 9mm Steyr SPP factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Eagle Import SPS 21 Round 9mm/.38 Magazines

- Fits 21 round 9mm/38super Factory Eagle Import SPS magazines. 
- Easy installation into the follower.
- Limits the magazine to 10 rounds of 9mm/38super. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

Magblock 10 Round Limiter for Kimber Mako R7 (9mm) 13 Round Magazines

- Fits 13 round 9mm magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Kimber Mako R7 13 round magazine.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield XDM Elite 9mm Magblock

- Fits 20 round 9mm XDM magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Springfield XDM Elite 9mm Magblock

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 21 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/21 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

ETS Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm ETS M&P magazines (ONLY). 
- New design installs into the follower like in the pictures.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with ETS S&W Magazines.

-This block is for the ETS S&W M&P 9mm 17-round magazine only.

ETS Glock 9mm Magblock 10 Round Limiter for 31 round Magazines

This Magblock fits the ETS 31 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/31 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

Magblock 10 Round Limiter for CZ-75 SP-01 18 Round Magazines

- Fits 18 round 9mm CZ-75 SP-01 magazines.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*If using our Universal Limiter for this magazine: Cut to #21 and glue flush at the bottom for 10/18 limiter. Slide lock is not used. When epoxy cures assemble magazine. #21 will show in the limiter window notch like in the photos.