Pistols

Magblock 10 Round Limiter for B&T 30 Round Magazines

- Fits 30 round 9mm B&T factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 -Block will work in B&T TP9, APC9, MP9, and GHM9 30-round magazines.

Sig Sauer P322 .22LR Magblock 10 & 15 Round Limiter

- This block will convert 20 round Sig P322 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for Ruger Max 9 (9mm) 12 Round Magazines

- Fits 12 round 9mm magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Ruger Max 9. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Walther WMP (.22Magnum) Magblock 10 Round Limiter for 15 Round Magazine

- Fits 15 round .22 Walther WMP .22 magazines. 
- Easy installation by using the stock locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for CZ-82, CZ-83 (.380 and 9x18) 12 Round Magazines

- Fits 12 round .380, 9x18 CZ-82, CZ-83 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of .380 and 9x18.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on CZ55 - CZ-82, CZ-83 factory magazines

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Smith & Wesson 5900, 459, 559, & 659 Series Magblock 10/14 (9mm)

This Magblock fits the Smith & Wesson 5900 Series 14 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds under the magazine follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/14 S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

-Block is designed for the 14 round, black follower, early version, 659 series magazines. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Taurus G3 Magblock 10/17 and 15/17 (9mm) 10 and 15 Round Limiter

This Magblock fits the factory Taurus G3 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus G3 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all. 

Walther PDP Compact Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Walther PDP Compact magazines as shown.
- Tested in Walther PDP Compact Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit.

-This block will fit the new PDP-F magazines. 

Beretta PX4 Full Size Tactical Magblock 10/17 (.40) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round .40 caliber magazines and will limit them to 10 rounds. Installs at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired. (This block is for the tactical version magazine).

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines in .40S&W.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 (.40) magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield XDM Elite Compact 9mm Magblock 10/14

- Fits 14 round 9mm XDM Elite Compact magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Springfield XDM Elite Compact 9mm Magblock

Springfield XD 9mm 10/15 Round Magblock

• Fits 15 round XD and XD Mod 2 9mm magazines. 
• Easy installation at the base of the magazine.
• Limits the magazine to 10 rounds of 9mm.
• Can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

*This block is designed for the factory 15 round magazine, made by Springfield. Will not work on Promag XD magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Taurus TX-22  (.22LR) Magblock 10 Round Limiter for 16 Round Magazine.

- Fits 16 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

ProMag Springfield XD-9 9mm Magblock

- Fits 19 round 9mm XD-9 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

ProMag Springfield XD-9 9mm Magblock