Pistols

Magblock 10 Round Limiter for Sarsilmaz ST45 .45 magazines

- Fits 12 round .45 Sarsilmaz ST45 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Sarsilmaz ST45 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Taurus TX-22  (.22LR) Magblock 10 Round Limiter 

- Fits 15 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock For Rock Island Armory/Armscor Tac Ultra A2 1911 Double Stack 16 Round 10mm/.40 Magazines

- Fits 16 round 10mm/.40 RIA A2 1911 Double Stack and Tac Ultra magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 10mm/.40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Amend2 Glock 9mm Magblock for 34 Round (9mm) Magazines

- Fits 34 round 9mm Amend2 Glock 17 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Amend2 Glock Magazines.
Only compatable with the follower type and magazine base extension shown in the pictures. If yours is different then modifications may be needed.

Amend2 Glock 22 (.40) Magblock

- Fits 15 round .40 Amend2 Glock 22 magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Amend2 Glock 23 (.40) Magblock

- Fits 13 round .40 Amend2 Glock 23 magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Shield Arms Glock 43X and Glock 48 (9mm) Magblock

- Fits Shield Arms 15 round 9mm Glock 43x and Glock 48 only and won't work in the new Glock 43x, 48 factory 15-round magazines.
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Note: This block will work in Gen 1, Gen 2, and Gen 3 magazines.

Attention: This block is not intended to work in the new Factory Glock 43x, 48 15-round magaiznes. If you use this block in the factory Glock 43x magazines then there's a chance you will be able to load an 11th round into the magazine. 

**SCROLL to the bottom of the page for a block for the factory Glock 43x, 48 magazine. 

Taurus G3 Magblock 10/17 and 15/17 (9mm) 10 and 15 Round Limiter

This Magblock fits the factory Taurus G3 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus G3 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all. 

Walther PDP Compact Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Walther PDP Compact magazines as shown.
- Tested in Walther PDP Compact Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit.

-This block will fit the new PDP-F magazines. 

Glock 23 (9mm) Magblock (For Older Style Followers Only)

- Fits 13 round .40 Foctory Glock 23 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits older style follower Glock Magazines only.
Only compatable with the follower type shown in the pictures. 

Magblock 10 Round Limiter for CZ Scorpion (.32) 20 Round Magazines

- Fits 20 round .32auto CZ Scorpion magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .32auto. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

 -This block will only work in the ,32 auto, 20 round magazine.

AREX Rex Zero S1 Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory AREX Rex Zero S1 magazines as shown.
- Tested in AREX Rex Zero S1 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Note: This block has only been tested with magazine that has the spring bunch at the bottom.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield OSP Elite Compact 10mm 10/11 Magblock

- Fits 11 round OSP Elite 10mm magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.