Walther .40 PPQ M2 Magblock 10 Round Limiters

- Fits 13 round .40 Factory Walther PPQ M2 magazines as shown.
- Tested in M2 version PPQ Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal just cut flush at the base with number #12 shown in the indicator notch. Cement together after testing fit. 

Hudson H9 9mm Magblock 10 and 15 Round Limiters

- Fits 17 round 9mm Factory  Hudson H9 9mm magazines.
- Easy installation at the base of the magazine. 
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Note: This limiter can also be made using our Universal Pistol Limiter and cutting flush at the base with #20 showing in the indicaor notch. 
The limiters shown here come pre-cut and glued for a drop in conversion. 

Magblock For Rock Island Armory/Armscor Tac Ultra A2 1911 Double Stack 16 Round 10mm/.40 Magazines

- Fits 16 round 10mm/.40 RIA A2 1911 Double Stack and Tac Ultra magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 10mm/.40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Taurus TX-22  (.22LR) Magblock 10 Round Limiter 

- Fits 15 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for Sarsilmaz ST45 .45 magazines

- Fits 12 round .45 Sarsilmaz ST45 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Sarsilmaz ST45 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

 Magblock 10 Round Limiter for Heckler & Koch USP 9mm Tactical

- Fits 31 round 9mm H&K USP9 Tactical magazines. 
- Limits the magazinbe to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

SAR-9 Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory Sarsilmaz SAR-9 magazines as shown.
- Tested in SAR9 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 14 shown in the indicator notch. Cement together after testing fit. 

Magblock 10 Round Limiter for Sig Sauer 2022 SigPro 9mm 17 Round Magazines. Fits 2022 and 2009

- Fits 17 round 9mm Factory Sig Pro magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

The Universal limiter can be used to make this block by cutting flush with the base with #20 showing in the indicator notch. The blocks sold here are pre-cut and fixed at this length. 

ETS Glock .40 Magblock 10 Round Limiter for 19 round Magazines

This Magblock fits the ETS 19 round .40 magazines for Glocks and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/19 Glock .40 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

 *This block is designed for the ETS Glock .40 19 round magazine only. If used in other magazines it might need to be modified. 

ETS Glock 22 (.40) Magblock

- Fits 16 round .40 ETS Glock 22 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .40 ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 ATTENTION: This block is designed for the ETS Glock 22 magazine only. 

Magblock 10 Round Limiter for Grand Power K100 20 Round Magazines

- Fits 20 round 9mm Factory Grand Power K100 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #20 showing in the notch to make this limiter. 

Magblock 10 Round Limiter for Grand Power K100 P1 15 Round Magazines

- Fits 15 round 9mm Factory Grand Power K100 P1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 P1 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #10 showing in the notch to make this limiter. 

Smith & Wesson SW99 9mm Magblock 10 Round Limiters

- Fits 16 round 9mm SW99 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W SW99 16 Round Magazines. 

*Universal Pistol Limiter Instructions: Cut to #16 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  

Taurus PT1911 Magblock 5/8 (.45) 5 Round Limiter for Hunting

This Magblock fits the factory Taurus PT1911 8 round .45acp magazines and will limit them to 5 rounds for hunting. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 5/8 Taurus PT1911 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT1911 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.