Pistols

Smith & Wesson M&P .40 2.0 Magblock 10 Round Limiter

- Fits 15 round .40 M&P 2.0 and Non 2.0 Magazines. 
- Easy installation on top of the locking plate.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Will only fit 2.0 version. Other versions require a shlightly shorter limiter.  

Attention: Smith and Wesson has just recently changed their locking plate/floor plate design. You will need to determine which type you have. Please see pictures below.

Ruger Security 9 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Ruger Security 9, 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10 round Ruger Security 9 Magazines.

-No modification to the magazine is required. The spring bottom can fit into the drilled hole in the limiter or you can bend the spring if desired.

-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "9" showing in the indicator notch. Cement the base and slide together. Drill a hole to allow room for the spring as shown in the photos or just bend the spring straight at the bottom with pliers.

Magblock 10 Round Limiter for CZ P-07 Duty (9mm) 16 Round Magazines

- Fits 16 Round 9mm CZ P-07 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Patented Design 

*** Universal Pistol Limiter Instructions: Cut to "11" showing in the indicator notch and a flush base. (Ordering here is for pre-cut and finished blocks for a drop in limiter.)

Beretta PX4 Full Size Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 15 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/15 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 15 round Beretta PX4 magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

 Magblock 10 Round Limiter for Heckler & Koch USP and P30 .40

 - Fits 13 round .40 H&K USP and P30 magazines. 
- Limits the magazinbe to 10 rounds of .40
- Easy installation at the base of the magazine. Sits on top of the locking plate as shown.
- Held in place with tension or can be epoxied in place.
- Lightweight, efficient design. 

FYI: The Universal Pistol Limiter cut to "6" in the indicator notch with a flush base works to limit this magazine to 10 rounds.

Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 15 round 9mm M&P full size magazines. (Identified by extra spring coils at the base) 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 15 Round Magazines. 

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*Universal Pistol Limiter Instructions: Cut to #14 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #14 will show in the limiter window notch like in the photos.  

*This block will not work on M&P Compact 9mm magazines, and are only designed for Full-Size magazines.

Glock 19X Magblock 10/19 (9mm)

This Magblock fits the Glock 19X magazines with the +2 extended base. (19 round magazines)  and will limit them to 10 rounds.  

- This is a 2 part limiter. It is a -17 round limiter under the follower, then a -2 adapter to limit the extended floorplate.

- Easily installed in seconds. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/19 Glock 19X magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

PATENT # 9328982 B2, Additional Patents Pending

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

 Magblock 10 Round Limiter for Heckler & Koch USP, P30 and VP9 9mm

- Fits 15 round 9mm H&K USP, P30 and VP9 magazines. 
- Limits the magazinbe to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This block is made from our Universal Pistol Limiter and is cut so that the number "9" shows up in the indicator notch. The lock tab is not used and the slide is cut so that it is flush with the base of the limiter. The 2 pieces are then bonded together. See photos for details. 

Magblock 10 Round Limiter for CZ 75 Compact and Subcompact 9mm 14 Round Magazines by Mec-Gar

- Fits 14 round 9mm CZ-75 compact and subcompact magazines as shown in the photos.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested on CZ-75 magazines made by Mec-Gar as shown in the photos. CZ brand factory magazines are listed as a different product.

*If using our Universal Limiter for this magazine: Cut to #6 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. #6 will show in the limiter window notch like in the photos.  

Walther PPQ .45 Magblock 10 Round Limiter

This Magblock fits the Walther PPQ .45 12 round magazines and will limit them to 10 rounds of .45mm  Easily installed in seconds under the follower as shown. It is held in place with spring tension alone or can be glued or epoxied if required.
- Simple install to make 10 round Walther PPQ and P99 Magazines.
- Will also work in M2 version PPQ Magazines
- No external modification to the magazine is required.

FYI: Universal Limiter Instructions 
To make this limiter out of the Universal Limiter just cut flush at the base with number 4 showing in the indicator notch. Cement together after testing fit. 

Ruger BX-25 Magblock 10 Round Limiters

- Fits 25 round 22LR Ruger BX25 magazines.
- Easy installation.
- Limits the magazine to 10 rounds of 22LR
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Magblock 10 Round Limiter for Browning Hi Power 15 Round Magazines made by Mec Gar

- Only for use in the magazine type pictured.

- Fits 15 round 9mm Hi Power magazines by Mec Gar.
- Easy installation at the base of the magzine.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.
- Made using our Universal Pistol Limiters pre-cut and fixed at #15.

Magblock 10 Round Limiter for Browning Hi Power 20 Round Magazines

- Please note that different followers exist for Hi Power magazines. Please see the photos to determine which followers your magazines use. Only for use with the follower type shown. Modification would be required for other follower types.

Magblock 10 Round Limiter for CZ-75 (.40) 12 Round Magazines

- Fits 12 round .40 CZ-75 SP-01 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on CZ-75 magazines made by Mec-Gar as shown in the photos. Has also been reported to work with factory magazines. The block may need to be modified to work with magazines from other manufactures.
- *Same as P229 .40 10/12 limier