Pistols

Shadow System CR920, CR920P Factory 10/13  (9mm) Magblock

- Fits 13 round 9mm Shadow System CR920, CR920p, and CR920 War Poet  magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 -Block is designed to work in the Shadow Systems subcompact pistol magazine, made by Shadown Systems.

Magblock 10 Round Limiter for Sig P226 Mec-Gar 20 Round Magazines

- Fits 20 round 9mm Sig P226 Italian made magazines as pictured
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*These blocks will not work in the Sig Sauer branded P226 X-Five/Legion 20-round magazines, as well as Mecgar Competition 20-round magazines. We sell blocks for those magazines located in our P226 section.

Smith & Wesson SD40 VE .40 Magblock 10 Round Limiters

- Fits 14 round .40 SD40VE, SD40G, SD40E, SD40P, SD40V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40 cal. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 14 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #8-9 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #8-9 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

MecGar Beretta 92FS, M9, 92XI Magblock 10/18 (9mm) 10 Round Limiter

This Magblock fits the Mec-Gar branded Beretta 92FS - M9 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 MecGar made Beretta 92FS/M9 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on Mec-Gar (M9) Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions and the magazines this block works in correctly. Part#MGPB9218AFC / UD8A0601P

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield Hellcat 9mm 10/11 Magblock

- Fits 11 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 5 Round Limiter for CZ Scorpion Evo (9mm) 20 Round Magazines

- Fits 20 round 9mm CZ Scorpion Evo magazines
- Easy installation at the base of the spring.
- Limits the magazine to 5 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

 Magblock 10 Round Limiter for Heckler & Koch USP9 Compact & P2000 Full-size Magazine

- Fits 13 round 9mm H&K USP, P2000 full-size magazines. 
- Limits the magazinbe to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This block is made from our Universal Pistol Limiter and is cut so that the number "5" shows up in the indicator notch. The lock tab is not used and the slide is cut so that it is flush with the base of the limiter. The 2 pieces are then bonded together. See photos for details. 

Great for the range bag and to show your magazines are blocked. 

Also for patch collectors like myself :)

- 3” Round PVC 

- Hook and loop backing 

Beretta 81 Magblock 10/12 (.32) 10 Round Limiter

This Magblock fits the factory Beretta 81, 81B, 81BB 12 round .32 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/12 Beretta 81 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 81 magazines as shown in the photos. Other types of magazines may require modification of the limiter. 
*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Beretta 96FS MecGar Magblock 10/13 (.40) 10 Round Limiter

This Magblock fits the MecGar Beretta 96FS 13 round magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 96FS magazines.
- Save time and money and keep your magazines legal. 
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" MecGar 96 magazines as seen in the photos.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

 Magblock 10 Round Limiter for Heckler & Koch USP Expect 9mm

- Fits 18 round 9mm H&K USP expert magazines. 
- Limits the magazinbe to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This block is made from our Universal Pistol Limiter and is cut so that the number "16" shows up in the indicator notch. The lock tab is not used and the slide is cut so that it is flush with the base of the limiter. The 2 pieces are then bonded together. See photos for details. 

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield XDM .40 Magblock 10 Round Limiter

• Fits 16 round XDM .40 magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of .40
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

Smith & Wesson M&P .40 Magblock 10 Round Limiter

- Fits 15 round .40 M&P magazines. 
- Easy installation on top of the locking plate.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Will not fit 2.0 version which needs a slightly longer version  

*Universal Limiter Instructions: Cut to #8 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #8 will show in the limiter window notch like in the photos.