Ruger SR40 10/15 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Ruger SR40 .40, 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger SR40 Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "12" showing in the indicator notch. Cement the base and slide together.

FNS-40 and FNX-40 Magblock 10 Round Limiter for 14 Round Magazines (.40)

- Fits 14 round FNX-40 and FNS-40 Factory magazines. 
- Save time and money with this simple part. 
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

FYI: The Universal limiter can also be used to make this block. Cut the universal limiter to #12 show in the indicator notch. 

Smith & Wesson SD9 VE 9mm Magblock 10 Round Limiters

- Fits 16 round 9mm SD9VE, SD9G, SD9E, SD9P, SD9V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 16 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #12-13 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #12-13 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

Magblock 10 Round Limiter for CZ-75B 15 Round Magazines

- Fits 15 round 9mm CZ75B factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #10 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #10 will show in the limiter window notch like in the photos.  

Hudson H9 9mm Magblock 10 Round Limiters

- Fits 15 round 9mm Factory  Hudson H9 9mm magazines.
- Easy installation at the base of the magazine. 
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Note: This limiter can also be made using our Universal Pistol Limiter and cutting flush at the base with #12 showing in the indicaor notch. 
The limiters shown here come pre-cut and glued for a drop in conversion. 

Taurus PT92 and PT99 Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT92 and PT99 15 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. Save time and money converting your magazines to 10 rounds. It is held in place with spring tension alone or can be glued or epoxied if a permanent modification is needed to be legal.

- Simple install to make 10/15 Taurus PT92 and PT99 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT92/PT99 magazines as shown in the photos. Magazines marked "Made in Brazil" with metal followers. Other types of magazines will require modification of the limiter or a different size.

Please click on photos for installation instructions.

FYI: This limiter can also be made using our Universal limiter kit. Cut the Universal Pistol limiter flush at the base with the #9 showing in the indicator notch then set in place using glue. * The right rear part at the base of the limiter may need to be sanded down if it interferes with the magazine relaease hole. (See photos)

Magblock 10 Round Limiter for STI Staccato - Checkmate 170mm 20 Round 9mm Magazines

- Fits 26 round 9mm Factory Staccato - Checkmate 170 mm magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

*Note: If you have a newer Staccato STI magazine that has G3 on the back of the magazine, then you will need to click G3 option below. If you're running the Checkmate 170mm magazines, then choose the G3 options.

Ruger SR9 and SR9C 10/17 Magblock 10 Round Limiter for 17 Round Magazines

This Magblock fits the Ruger SR9 ands SR9C 9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger SR9 Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "14" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

Smith & Wesson M&P .40 2.0 Magblock 10 Round Limiter for 13 Round Magazines

- Fits 13 round .40 M&P 2.0 Magazines. 
- Easy installation on top of the locking plate.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Will only fit 2.0 version. 

*Universal Limiter Instructions: Cut to #5 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #5 will show in the limiter window notch.  

Attention: Smith and Wesson has just recenlty changing their locking plate/floor plate design. You will need to determine which type you have. Please see pictures below.

Magblock 10 Round Limiter for Sig P365/XL 15 Round Magazines

- Fits 15 round 9mm Factory Sig P365 magazines. 
- Save time and money with a simple install.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification where required to be legal. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield Hellcat 9mm 10/13 Magblock

- Fits 13 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for CZ P-07, P-10, P-09 Nocturne Compact 15 Round Magazines

- Fits 15 round 9mm CZ P-07, P-10, P-09 Nocturne Compact factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #9 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #9 will show in the limiter window notch like in the photos.  

 Magblock 10 and 15 Round Limiter for Heckler & Koch P30 and VP9 9mm

- Fits 20 round 9mm H&K P30 and VP9 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This block is made from our Universal Pistol Limiter and is cut so that the number "22" shows up in the indicator notch. The lock tab is not used and the slide is cut so that it is flush with the base of the limiter. The 2 pieces are then bonded together. See photos for details. 

-This block is for factory HK 20 round VP9/P30 magazines, and will not work on magazines with HK +5 extensions.

Magblock 10 Round Limiter for CZ P-10 Compact - P-09 Nocturne Compact 17 Round Magazines

- Fits 17 round 9mm CZ P-10 Compact factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #17 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. #17 will show in the limiter window notch like in the photos.