Pistols

Magblock 10 Round Limiter Girsan Witness2311, Checkmate and Kimber 11 Round .45 Magazines

- Fits 11 round .45 Girsan Witness2311 magazine made by Checkmate. 
- Easy installation into the follower of the magazine.
- Limits the magazine to 10 rounds of .45
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

-This block has been tested on Girsan Witness 2311 magazine made by Checkmate. This block has not been tested on any other brand of magazine.

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

 Magblock 10 Round Limiter for Diamondback AM2 9mm

- Fits 12 round 9mm Diamondback AM2 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation under the follower as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

 Magblock 10 Round Limiter for Diamondback AM2 9mm

- Fits 17 round 9mm Diamondback AM2 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation under the follower as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for Sig P365 .380 auto12 Round Magazines

- Fits 12 round .380 auto Factory Sig P365-380, P365 Luxe AXG, P365-380 Rose magazines. 
- Save time and money with a simple install.
- Easy installation at the base of the spring, with the bottom of the block locking into the base locking plate.
- Limits the magazine to 10 rounds of .380. 
- Held in place with spring tension or can be epoxied for a permanent modification where required to be legal. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

- This block is designed for the P365 .380 12-round magazine, and will not work in 9mm P365 magazines

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Ruger LC Carbine - SGM Tactical Glock 10mm Magblock 10 and 15 Round Limiter for 30 Round Magazines

- Fits 30 round Ruger LC Carbine / SGM Tactical Glock 10mm magazines manufactured in Korea.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 or 15 rounds of 10mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Ruger LC Carbine  (.45) Magblock

- Fits 13 round .45 caliber Glock 21 and 41 magazines.  *See details on correct follower types below. 
-Will also fit Korean Glock Magazines.  
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .45 caliber ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

* Uses a cut off Glock Limiter. The end will not end on a rib, so is not as smooth of a cut, but works great. 

* This block will work in the Ruger LC Carbine 13-round magazine made by Glock or SGM chambered in .45 acp.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Walther PDP Pro, Pro-X, Pro-E, Pro-SD Magblock 10 & 15 Round Limiters

- Fits 18 round 9mm Factory Walther PDP magazines w/ a +2 factory extension as shown.
- Tested in Walther PDP Pro Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Taurus TX-22 Toro (.22LR) Magblock 10 Round Limiter for 22 Round Magazine.

- Fits 22 round Taurus TX-22 Toro magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Mecgar Smith & Wesson 5900 Series Magblock 10/15 (9mm)

This Magblock fits the Mecgar Smith & Wesson 5900 Series 15 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine, and It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/15 Mecgar S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

-This block will also work on the Lionheart LH9 15-round magazines.

*This block has been tested on the MecGar Smith and Wesson 5900 series magazines only, and will not work in the factory S&W magazines.

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for STI Staccato CS/C Compact 15 Round 9mm Magazines

- Fits 15 round 9mm Factory Staccato STI CS/C  Compact magazines only and won't fit the newer 15-round full-size CS/C magaiznes. 
- Easy installation into the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for STI Staccato CS/C 15 Round 9mm Magazines

- Fits 17 round 9mm Factory Staccato STI CS/C  magazines. 
- Easy installation into the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Rost Martin RM1C - RM1S 9mm Magblock 10 Round Limiters

- Fits 15 round 9mm Rost Martin RM1C Magazine
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Rost Martin RM1C 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm Rost Martin RM1C Magazine
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Walther PDP Taylor Freelance +3 Extension Magblock 10 Round Limiters

- Fits 18 round 9mm Factory Walther PDP magazines as shown that are using Taylor Freelance +3 Extensions.
- Tested in Walther PDP Magazines w/ Taylor Freelance +3 extension.
- Easy installation under the follower like seen in the photos.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

-ATTENTION: Walther has recently changed their locking plate design. So you need to determine which size locking plate you have. An easy way to tell is the new magazines have the blue follower and thin locking plate.

*This block will only work in the newer Walther PDP magazines, shown in the photos.

SEE PICS for example. 

This listing is for Magblocks only, and not for Taylor Freelance +3 Extensions.

*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.