Promag Beretta 92F Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the Promag Beretta 92F 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Promag Beretta 92F magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Will only work on Promag Beretta 92F (PM Part# BER-A12) magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Promag Beretta PX4 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the Promag Beretta PX4 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Promag Beretta PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Will only work on Promag Beretta PX4 (PM Part# BER-A14) magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all. 

Magblock 10 Round Limiter for Tisas PX-5.7 20 Round Magazines

- Fits 20 round 5.7x28mm PX-5.7 factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7x28mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Act-Mag - Armscor Sig Sauer P320 17 Round Magazines

- Fits 17 round 9mm Act-Mag - Armscor Sig P320 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant polymer.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

*This block is designed for the Act-Mag - Armscor Sig P320 17-round magazines. This block won't work in factory Sig Sauer P320 magazines.

Glock 9mm Magblock for 33 Round (9mm) Magazines

- Fits 35 round 9mm Toolman Tactical Glock 35 round magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. This block has been designed and tested for the Toolman Tactical Glock 35-round magazine.

Glock 25 (.380) Magblock

- Fits 15 round .380 auto caliber Glock 25.  

- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .380 auto caliber ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block has only been tested on factory Glock magazines, and will not work in aftermarket magaziens without modifcation. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

PSA Dagger Micro (9mm) Magblock

- Fits PSA Dagger Micro 15 round 9mm.
- Easy installation under the follower of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Glock 17 (9mm) Magblock (For Older Style Followers Only)

- Fits 17 round 9mm Foctory Glock 17 magazines.  *See details on correct follower types below. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits older style follower Glock Magazines only.
Only compatable with the follower type shown in the pictures. 

Daniel H9 9mm Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Daniel Defense H9 9mm magazines.
- Easy installation at the base of the magazine. 
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for MAGPUL AMAG 17 SIG P320 17 Round Magazines

- Fits 17 round 9mm Magpul Amag 17 SG9 Sig P320 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant polymer.

*This block is designed for the New MAGPUL AMAG 17 SG9 P320 17-round magazines. This block won't work in factory Sig Sauer P320 magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Taurus TH45 Magblock 10/13 (.45) 10 Round Limiter

This Magblock fits the factory Taurus TH45 13 round .45 magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Taurus TH45 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus TH45 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Magblock 10 Round Limiter for Sig P226 17 Round Mec-Gar Magazines

This Magblock fits the Sig P226 Mec-Gar 17 round magazines and will limit them to 10 rounds. These blocks are for the Sig Sauer branded magazines made by Mec-gar. These magazines are found on Sig Sauer's website.

- Easy installation at the base of the spring.

- Limits the magazine to 10 rounds of 9mm.

- Held in place with spring tension or can be epoxied for a permanent modification.

- Lightweight, efficient design.

- Made of a super strong, heat resistant, fiber reinforced polymer.

Block used is a Universal Pistol Limiter cut to #17.

Magblock 10 Round Limiter for Steyr SPP 15 Round Magazines

- Fits 15 round 9mm Steyr SPP factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for H&K MP7 4.6x30mm 30 Round Magazines

- Fits 30 round 4.6x30mm HK MP7 factory magazines.
- Limits the magazine to 10 rounds of 4.6x30mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- See video below for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.