Pistols

Genuine Factory Beretta 92FS Magblock 10/18 (9mm) 10 & 15 Round Limiter

This Magblock fits the factory Beretta 92FS Series 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta 92 Series magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92FS 18 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/18 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 Attention: Make sure to verify what magazine you have before ordering.This block will fit the following 18-round 92FS series magazines:

Beretta 90-two, Beretta 92G, Beretta M9, Beretta 92D, Beretta 92 Vertec, Beretta 92F

Magblock 10 Round Limiter for STI Staccato 120mm 16 Round 9mm Magazines

- Fits 16 round 9mm Factory Staccato STI C2 120 mm magazines. 
- Easy installation into the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

*Note: If you have a newer Staccato STI magazine that has G3 on the back of the magazine, then you will need to click G3 option below.

Magblock 10 Round Limiter for CZ P-10F (.45) 13 Round Magazines

- Fits 13 round .45 CZ P-10F magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45 ACP. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Glock 20, 40 (10mm) Factory 10 Round Magazine Magblock 

- Fits 10 round 10mm Glock 20 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 5 rounds of 10mm ammunition for hunting. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block is design to limit Factory Glock (10mm) 10 round magazines to 5 rounds for hunting.

Magblock 10 Round Limiter for Zenith ZF-5 MP5 9mm 30 Round Magazines

- Fits 30 round 9mm Zenith MP5 style magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. (Follower insert requires epoxy or silicone to securely hold in place).
- Lightweight, efficient design. 

NOTE: This block is designed for the Zenith ZF-5 MP5 Stye magazines only. This block is longer then the standard H&K MP5 Magblock and won't work in the HK MP5 factory magazines. 
 

Stoeger STR-9 9mm Magblock 10 Round Limiter for 15 Round Magazine

- Fits 15 round 9mm Stoeger STR-9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Century Arms OEM AP5 MP5 9mm 30 Round Magazines

- Fits 30 round 9mm Century Arms OEM MP5 style magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

NOTE: This block is designed for the Century Arms OEM MP5 Magazines and the factory H&K MP5 magazines.
 

Taurus PT909 and PT809 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT909 and PT809 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Taurus PT909 and PT8099 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT909/PT809 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Magblock 10 Round Limiter for AC-Unity MP5 9mm 30 Round Magazines

- Fits 30 round 9mm AC-Unity MP5 style magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

NOTE: This block is designed for the AC-Unity MP5 Magazines.
 

Smith & Wesson M&P Shield Plus, Equalizer 9mm Magblock 10 Round Limiter

- Fits 15 round 9mm M&P Equalizer/Shield Plus magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Brownells - Meccanica Del Sarca CZ-75 15 Round "Red Follower" Magazines

- Fits 15 round 9mm CZ75 Brownells magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #15 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #15 will show in the limiter window notch like in the photos.  

 ATTENTION:  This block is designed for the Brownells - Meccanica Del Sarca CZ-75 15 round magazines only. This block won't function correctly in factory or MecGar 15 round CZ-75 magazines. These magazines are sold by Brownells.com, and have a distinctive red follower that have a circler point under the follower piece (See: pictures for examples). 

Promag FN Five-Seven Magblock 10 Round Limiter

- Fits 30 round 5.7 mm Promag FN magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

ETS Glock 9mm Magblock 10 Round Limiter for 32 round Magazines

This Magblock fits the ETS 32 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/32 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

*This block is designed for the ETS 32 Glock magazines only. If used in other magazines it might need to be modified.

FN510 Tactical 10mm Magblock 10 Round Limiters for 22 Round Magazine

- Fits 22 round 10mm FN510 Tactical 10mm magazines. 
- Limits the magazine to 10 rounds of 10mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory FN510 10mm 22 round magazine