Magblocks

IWI MecGar Jericho 941 Magblock 10 Round Limiter

- Fits 16 round 9 mm Made in Italy MecGar IWI Jericho magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block fits both 16 Round and 17 Round IWI Jericho 941 "Made in Italy" magazines. Tested on the magazine in the photos.  

IWI MASADA Magblock 10 Round Limiter

- Fits 17 round 9 mm Made in Italy IWI MASADA magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Taurus PT1911 Magblock 5/8 (.45) 5 Round Limiter for Hunting

This Magblock fits the factory Taurus PT1911 8 round .45acp magazines and will limit them to 5 rounds for hunting. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 5/8 Taurus PT1911 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT1911 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Smith & Wesson SW99 9mm Magblock 10 Round Limiters

- Fits 16 round 9mm SW99 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W SW99 16 Round Magazines. 

*Universal Pistol Limiter Instructions: Cut to #16 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  

Magblock 10 Round Limiter for Grand Power K100 P1 15 Round Magazines

- Fits 15 round 9mm Factory Grand Power K100 P1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 P1 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #10 showing in the notch to make this limiter. 

Magblock 10 Round Limiter for Grand Power K100 20 Round Magazines

- Fits 20 round 9mm Factory Grand Power K100 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #20 showing in the notch to make this limiter. 

Taurus PT24/7 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT24/7 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Taurus PT24/7 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT24/7 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Beretta APX Magblock 10/15 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 15 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #9 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #9 will show in the limiter window notch like in the photos. 

 Wilson Combat EDC X9S Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Wilson Combact EDC X9S magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

Beretta APX Magblock 10/18 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 18 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #20 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #20 will show in the limiter window notch like in the photos. 

 Wilson Combat EDC X9 Magblock 10 Round Limiters for 18 Round Magazine

- Fits 18 round 9mm Factory Wilson Combact EDC X9 magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

Magblock 10 Round Limiter for Remington 1911 R1 9mm magazines

- Fits 19 round 9mm Remington 1911R1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for STI Staccato 126mm 17 Round 9mm Magazines

- Fits 17 round 9mm Factory Staccato STI P, XC, XL 126 mm magazines. 
- Easy installation into the follower of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

*Note: If you have a newer Staccato STI magazine that has G3 on the back of the magazine, then you will need to click G3 option below.

AREX Rex Delta Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory AREX Rex Delta magazines as shown.
- Tested in AREX Rex Delta 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 18 shown in the indicator notch. Cement together after testing fit.