Bersa Thunder Ultra Compact Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Bersa Thunder Ultra Compact 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder Ultra Compact 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/13 Bersa Thunder Plus Ultra Compact magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "6" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Kel-Tec CP33 22LR 10/33 Magblock 10 or 15 Round Limiter

- This block will convert 33 Kel-Tec-CP33 magazine into 10 round magazines.

- Easy to install without damage to your magazines.

Magblock 10 Round Limiter for Kalashnikov USA 9mm 30 Round magazine

- This block fits the new Kalashnikov USA 9mm magazines and will convert them to hold 10 rounds.

-Installs right under the follower and is held in place by spring tension.

- Made of super strong heat resistant polymer.

-This block is compatiable with the KR-9, KP-9 and KR-9 SBR magazines.

H&K Magblock 10/20 Limiter

- For use in HK417 and HK MR762 type 20 round magazines as pictured.

- These blocks will convert a 20 round magazine to hold only 10 rounds.

Magblock 10 Round Limiter for Canik TP9 Elite Sub-Comp 12 Round Magazines

- Fits 12 round 9mm Factory Canik TP9 Elite and Mete MC9 Subcompact magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Canik TP9 Subcompact 12 round magazine.The block may need to be modified to work with magazines from other manufactures.

ETS Glock .45 Magblock 10 Round Limiter for 40 round Magazines

This Magblock fits the ETS 30 round .45 magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/30 Glock .45 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

ETS Glock 9mm Magblock 10 Round Limiter for 40 round Magazines

This Magblock fits the ETS 40 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/40 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

-This magazine fits all Glock double stack 9mm firearms.

ETS Glock .40 Magblock 10 Round Limiter for 30 round Magazines

This Magblock fits the ETS 30 round .40 magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/30 Glock .40 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

CZ-75 Tactical Sport 10/17 Magblock 10 Round Limiter for 17 Round factory magazines

This Magblock fits the CZ-75 Tactical Sport 17 round magazines will limit them to 10 rounds. Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/17 CZ-75 magazines.

- No external modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

NOTE: Universal Limiter Instructions: Indicator notch should show "18" which is the maximum length, the base is flush.

Beretta PX4 Full Size Magblock 10/20 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 20 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. It is held in place with spring tension alone or can be glued or epoxied if desired. 

- Save time and your expensive factory magazines. Quick install to make 10/20 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 20 round Beretta PX4 magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Bersa Thunder Magblock 10/13 (.40) 10 Round Limiter

This Magblock fits the factory Bersa Thunder .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder .40 magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/13 Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "8" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

Bersa Thunder Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Bersa Thunder 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/17 Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "16" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

FN 509 Midsize, Compact & Edge Magblock 10 Round Limiter For 15 Round Magazines

- Fits 15 round 9 mm Factory FN 509 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Bulgarian AK-74 Magblock for 5.56x45mm 45 round magazine

- This AK-74 block and adapter fits the Bulgarian Smoothside 45 round polymer 5.56x45 mm magazines and will convert them to hold only 10 rounds.

- The new design features a spring catch which will allow an easy attachment point to the spring.

- This prevents the block making noise and epoxy can be added at this point to make it permanent.

- This block will replace the original magazine locking plate.

- This block won't work in the Circle 10 Bulgarian AK-74 chambered in 5.45x39. We sell a block just for that magazine. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.