Magblock 10 Round Limiter for ETS Sig P320 15 Round Magazines

- Fits 15 round 9mm ETS Sig P320 magazines. 
- Easy installation into the follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant polymer.

- This block will only work in ETS Sig P320 10/15 magazines. It will not work in Sig factory P320 magazine without modification. 

We make a block for the factory Sig P320 10/15 magazine. 

CETME 10/20 Magblock 

Fits CETME Military Surplus Magazines in .308/7.62x51mm 20 round magazines and will convert them to hold only 10 rounds.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

- May fit other brand AR 10 Magazines. 

Beretta APX Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Walther PPQ (.22LR) Magblock 10 Round Limiter 

- Fits 12 round .22 Walther PPQ .22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

 Magblock 10 Round Limiter for Heckler & Koch USP/P2000 Compact .40

 - Fits 12 round .40 H&K USP and P2000 magazines. 
- Limits the magazinbe to 10 rounds of .40
- Easy installation at the base of the magazine. Sits on top of the locking plate as shown.
- Held in place with tension or can be epoxied in place.
- Lightweight, efficient design. 

FYI: The Universal Pistol Limiter cut to "3" in the indicator notch with a flush base works to limit this magazine to 10 rounds.

Magblock 10 Round Limiter for ETS Sig P320 17 Round Magazines

- Fits 17 round 9mm ETS Sig P320 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant polymer.

- This block will only work in ETS Sig P320 10/17 magazines. **It will not work in Sig factory P320 magazine without modification. 

We make a block for the factory Sig P320 10/17 magazine. 

Colt 1911 (.22LR) Magblock 10 Round Limiter 

- Fits 12 round .22 Colt 1911 .22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Magblock 10 Round Limiter for Canik TP9 17 Round Magazines

- Fits 17 round 9mm Factory Canik TP9 Subcompact magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Canik TP9 Subcompact 17 round magazine.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #18 showing in the notch to make this limiter. 

Beretta PX4 Full Size Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Sig Sauer P320 and P250 Magblock 10 round limiter for 18 round magazines.

This Magblock fits the Sig P320 and P250 18 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/18 Sig Sauer P320 and P250 magazines. 

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Tested on factory Sig P320 and P250 18 round magazines. The block may need to be modified to work with magazines from other manufactures.

-NOTE: Universal Limiter Instructions: Use at maximum length with "22" showing in the indicator notch. Use the locking tab, but cut off the lock button for a flat base. Cement Together.

Ruger American 10/17 Magblock 10 Round Limiter for 17 Round Magazines

This Magblock fits the Ruger American Pistol  9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger American Pistol Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "18" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

FN 509 Tactical Magblock 10 Round Limiter for the 24 round magazine

- Fits 24 round 9 mm Factory FN 509 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 Magblock 10 Round Limiter for Heckler & Koch P30, VP9, and VP9 A1 F 9mm

- Fits 17 round 9mm H&K P30, VP9, VP9 A1 F magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation in the follower as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: We use a cut down XDM .40 10/16 block for this magazine.

 These will not work with the VP9/P30 15 round magazine. The 15 round magazine has a diffrent follower. 

Bersa Thunder Plus Magblock 10/15 (.380) 10 Round Limiter

This Magblock fits the factory Bersa Thunder 15 round .380 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder .380 magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/15 Bersa Thunder Plus magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "9" showing in the indicator notch. Also, sides and front of base sanded down. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done.