Ruger Five-Seven Magblock 10 & 15 Round Limiter

- Fits 20 round 5.7 mm Factory Ruger magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

Pmag 27 GL9 Magblock 10 Round Limiter 10/27

This Magblock fits the Magpul Pmag 27 GL9 magazines used in 9mm Glocks and will limit them to 10 rounds. It is held in place with spring tension alone or can be glued or epoxied if desired.

• Simple install to make 10/27 Pmag 27 GL9 Glock magazines.
• Save Time and Money converting your magazines.
• No modification to the magazine is required.
• Lightweight and will not interfere with magazine reliability.
• Patented Design 

Magblock 10/30 for ETS (Elite Tactical System) 

- For use in ETS type 30 round magazines for the AR15. 

- These blocks will convert a 30 round magazine to hold only 10 rounds. 

- This block has only been tested in the in the Gen 1 version of this magazine (See pictures for details).

HK416 22LR 10/20 Magblock 10 Round Limiter

- This block will convert 20 round HK 416 22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

Magblock 10 Round Limiter for CZ P-10 Sub-Compact 12 Round Magazines

- Fits 12 round 9mm CZ P-10 Sub-Compact factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Beretta 96 Magblock 10/11 (.40) 10 Round Limiter

This Magblock fits the factory Beretta 96 11 round magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/11 Beretta 96 magazines.
- Save time and money and keep your magazines legal. 
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 96 magazines as seen in the photos.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 15/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in 300 Blackout only.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 15 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.- Does not affect reliability.

- No increase in spring pressure. 

ASC - DURAMAG AR 7.62X39 10 & 15 ROUND LIMITER FOR 30 ROUND MAGAZINE

• New Design
• Converts the updated ASC AR-15 7.62x39 30 round magazine to 10 rounds.
• Easy installation 
• Does not affect reliability 

Springfield Hellcat 9mm 10/13 Magblock

- Fits 13 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock for Mossberg 590M 2 Round Limiter for 10 Round Magazines (12ga)

• Fits Mossberg 10 round magazines and will limit them to 2 rounds in the magazine for hunting. 
• Fits under the follower. The original plug will need to be removed by pulling out with pliers. See photos.
• Can be held in with included screw or epoxy if a permanent modification is needed. 

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in 300 Blackout only.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.- Does not affect reliability.

- No increase in spring pressure. 

Magblock 10 Round Limiter for Sig P365/XL 15 Round Magazines

- Fits 15 round 9mm Factory Sig P365 magazines. 
- Save time and money with a simple install.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification where required to be legal. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Smith & Wesson M&P .40 2.0 Magblock 10 Round Limiter for 13 Round Magazines

- Fits 13 round .40 M&P 2.0 Magazines. 
- Easy installation on top of the locking plate.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Will only fit 2.0 version. 

*Universal Limiter Instructions: Cut to #5 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #5 will show in the limiter window notch.  

Attention: Smith and Wesson has just recenlty changing their locking plate/floor plate design. You will need to determine which type you have. Please see pictures below.

Ruger SR9 and SR9C 10/17 Magblock 10 Round Limiter for 17 Round Magazines

This Magblock fits the Ruger SR9 ands SR9C 9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger SR9 Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "14" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications.