Magblocks

Springfield Hellcat 9mm 10/11 Magblock

- Fits 11 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

MecGar Beretta 92FS, M9, 92XI Magblock 10/18 (9mm) 10 Round Limiter

This Magblock fits the Mec-Gar branded Beretta 92FS - M9 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 MecGar made Beretta 92FS/M9 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on Mec-Gar (M9) Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions and the magazines this block works in correctly. Part#MGPB9218AFC / UD8A0601P

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Smith & Wesson SD40 VE .40 Magblock 10 Round Limiters

- Fits 14 round .40 SD40VE, SD40G, SD40E, SD40P, SD40V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40 cal. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 14 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #8-9 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #8-9 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

Magblock 10 Round Limiter for Sig P226 Mec-Gar 20 Round Magazines

- Fits 20 round 9mm Sig P226 Italian made magazines as pictured
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*These blocks will not work in the Sig Sauer branded P226 X-Five/Legion 20-round magazines, as well as Mecgar Competition 20-round magazines. We sell blocks for those magazines located in our P226 section.

Shadow System CR920, CR920P Factory 10/13  (9mm) Magblock

- Fits 13 round 9mm Shadow System CR920, CR920p, and CR920 War Poet  magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 -Block is designed to work in the Shadow Systems subcompact pistol magazine, made by Shadown Systems.

Magblock 10 Round Limiter for Pmag 12 GL9 Magazines.

- Fits 12 round Magpul Pmag GL9 magazines for Glock 26.

- Easy installation at the base of the magazine and sits on top of the locking plate.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits Magpul Pmag 12 GL9 Magazines Only. Will not fit standard Glock type Magazines.

H&K 417 Magblock 5/10 Limiter

- For use in H&K 417 - MR762  type 10 round magazines as pictured.

- These blocks will convert a 10 round magazine to hold only 5 rounds.

HK416 22LR 10/20 Magblock 10 Round Limiter

- This block will convert 20 round HK 416 22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

Fits Springfield M14/M1A 7.62x51mm/.308 15 round magazines.

- Easiest and quickest way to make a 10 round M14 Magazine.

- Can be permanently attached to the spring with epoxy.

- The block attaches to the spring to prevent noise and movement.

- No magazine modifications required.

-Allows loading on a closed bolt with 10 rounds installed.

Hexmag AR-10/SR25 Magblock 10/20

- Magblock 10/20 MCL block for use in polymer Hexmag AR-10/SR25 magazines.

- This block will convert a 7.62x51/.308 20 round magazine to hold only 10 rounds. 

- Uses the original Hexmag locking plates.

ProMag Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm ProMag M&P magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with ProMag S&W Magazines.

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*This block will only work in the Promag Smith and Wesson M&P 9mm magazines, and will not work in Factory M&P 9mm magazines. If you're blocking a factory S&W M&P 9mm 17-round magazine, you will need a different magblock.

Lancer L7 10/25 Limiter for 25 round magazines in .308/7.62x51mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 25 round magazine to hold only 10 rounds.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear. 
Note: This is a custom modified Pmag block and will replace the original base. 

Magblock 10/32 MCL (Magazine Capacity Limiter) for Daniel Defense 32 round magazines in .223/5.56mm.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure. 

Magblock 10 Round Limiter for Magpul PMAG 35 CZ Scorpion Evo 3 (9mm) 35 Round Magazines

- Fits 35 round 9mm Magpul PMAG 35 CZ Scorpion Evo and Daniel Defense PCC magazines
- Easy installation at the base of the spring on top of the original locking plate so you wont loose your original.
- Limits the magazine to 10 rounds of 9mm. 
- Lightweight, efficient design. 
- Made of a strong, heat resistant, polymer.

- The new Daniel Defense PCC 9mm is being issued with the Magpul PMAG CZ Evo 35-round magazine.