Magblocks

Magblock 10 Round Limiter for Grand Power K100 P1 15 Round Magazines

- Fits 15 round 9mm Factory Grand Power K100 P1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 P1 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #10 showing in the notch to make this limiter. 

Magblock 10 Round Limiter for Grand Power K100 20 Round Magazines

- Fits 20 round 9mm Factory Grand Power K100 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #20 showing in the notch to make this limiter. 

ETS Glock 22 (.40) Magblock

- Fits 16 round .40 ETS Glock 22 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .40 ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 ATTENTION: This block is designed for the ETS Glock 22 magazine only. 

ETS Glock .40 Magblock 10 Round Limiter for 19 round Magazines

This Magblock fits the ETS 19 round .40 magazines for Glocks and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/19 Glock .40 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

 *This block is designed for the ETS Glock .40 19 round magazine only. If used in other magazines it might need to be modified. 

Heckler & Koch UMP 9mm Magblock 10/30

- Works with H&K UMP 9mm 30 rd Magazines as shown.

-Uses the factory locking plate.

- Simple quick installation.

-Tested on USA made UMP 9mm 30 round magazines.

Magblock 10 Round Limiter for Sig Sauer 2022 SigPro 9mm 17 Round Magazines. Fits 2022 and 2009

- Fits 17 round 9mm Factory Sig Pro magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

The Universal limiter can be used to make this block by cutting flush with the base with #20 showing in the indicator notch. The blocks sold here are pre-cut and fixed at this length. 

SAR-9 Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory Sarsilmaz SAR-9 magazines as shown.
- Tested in SAR9 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 14 shown in the indicator notch. Cement together after testing fit. 

IWI MecGar Jericho 941, IWI Masada Slim Magblock 10 Round Limiter

- Fits 16 or 17 round 9 mm Made in Italy MecGar IWI Jericho magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block fits both 16 Round and 17 Round IWI Jericho 941 "Made in Italy" magazines. Tested on the magazine in the photos.  

Smith & Wesson SD9 VE 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm SD9VE, SD9G, SD9E, SD9P, SD9V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 17 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #16 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

FNX-9 Magblock 10 and 15 Round Limiters

- Fits 17 round 9 mm Factory FNX-9 magazines. 
- Easy installation under the follower.
- Limits the magazine to 10 or 15 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

10 Round Limiter for MSAR STG 42 Round Waffle Polymer Magazines

Magblock 10/42 MCL (Magazine Capacity Limiter) for MSAR STG 42 round polymer magazines in .223/5.56mm.

- This block will replace the lower spring attachment point or locking plate and convert a 42 round magazine to hold only 10 rounds.

- Customized base of the Magblock includes one locking point.

- Does not affect reliability.

- No increase in spring pressure.

-Tested on MSAR STG 42 round magazine only. 

Taurus TX-22  (.22LR) Magblock 10 Round Limiter 

- Fits 15 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

10 Round Limiter for MSAR STG 20 Round Waffle Polymer Magazines

Magblock 10/20 MCL (Magazine Capacity Limiter) for MSAR STG 20 round polymer magazines in .223/5.56mm.

- This block will replace the lower spring attachment point or locking plate and convert a 20 round magazine to hold only 10 rounds.

- Customized base of the Magblock includes one locking point.

- Does not affect reliability.

- No increase in spring pressure.

-Tested on MSAR STG 20 Round magazine only.

H&K AR-15 Polymer Magazine Magblock 10/30 Limiter

- For use in H&K MR556 and HK416 type 30 round polymer magazines as pictured.

- These blocks will convert a 30 round magazine to hold only 10 rounds.

*This block is desinged for the polymer magazine only.