FNP-9 Magblock 10 Round Limiter

- Fits 15 round 9 mm Factory FNP-9 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Beretta 92FS Magblock 10/20 (9mm) 10 Round Limiter for MecGar 20 Round Magazines.

This Magblock fits the MecGAr Beretta 92FS (20 round) 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/20 MecGar Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on MecGar Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

FN 509 Subcompact Magblock 10 Round Limiters

- Fits 12 round 9 mm Factory FN 509 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Promag Bersa Thunder Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the Promag Bersa Thunder 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Bersa Thunder 9mm magazines to 10 rounds. No external modification to the magazine is required. 

- Simple install to make 10/17 Promag Bersa Thunder High Capacity magazines. 
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original Promag Bersa Thunder magazines as shown in the photos. Other types of magazines will likely require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between number "19" showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

 Magblock 10 Round Limiter for ProMag Heckler & Koch VP9 9mm

- Fits 17 round 9mm ProMag H&K VP9 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This Magblock has been designed to be used with ProMag HK VP9 10/17 magazines. 

Will not work in factory HK magazines.

Magblock 10 Round Limiter for CZ P-09 (9mm) 21 Round Magazines

- Fits 21 round Tactical 9mm CZ P-09 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for H&K MP5 9mm 30 Round Magazines

- Fits 30 round 9mm HK MP5 factory magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. (Block installs into the follower and not at the base of the magazine).
- Lightweight, efficient design. 

ATTENTION: This block will not work in the Zenith MP5 style magazines. We have blocks listed for that under Zenith ZF-5
 

Magblock 10 Round Limiter for Remington 1911 R1 .40 magazines

- Fits 18 round .40 Remington RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 .40 double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Remington 1911 R1 9mm magazines

- Fits 18 round 9mm Remingto RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Remington RP9 9mm magazines

- Fits 18 round 9mm Remingto RP9 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington RP9 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Remington RP45 .45 magazines

- Fits 15 round .45 Remingto RP45 and 1911 R1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 & RP45 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for Para Ordnance P12 .45 magazines

- Fits 12 round .45 Para Ordnance P12 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Para Ordnance P12 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

*This block is made using a Universal Pistol block cut to #3.

Magblock 10 Round Limiter for Para Ordnance P13 .45 magazines

- Fits 13 round .45 Para Ordnance P13 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Para Ordnance P13 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

*This block is made using a Universal Pistol block cut to #5.

Amend2 Glock 19 (9mm) Magblock

- Fits 15 round 9mm Amend2 Glock 19 magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.