Magblocks

Pmag LR20 Magblock GEN M3 Magazine Capacity Limiters (5, 10, and 15 Round Limiters Available)

Fits the Magpul LR20 .308/7.62x51mm Pmags and will convert them to hold only 5, 10, or 15 rounds. Select desired size below. Easy to install. 

- Will NOT fit older version magazines. Gen M3 Only.

- Dust covers still fit with 10 rounds loaded.

- Load magazines on a closed bolt in most rifles.

- Easy to install.

- No external magazine modifications.

-This block requires you use the factory Magpul locking plate with our block (See picture 1 and 2). 

15 Round Limiter for CAA Indicative 30 Round Polymer Magazines

Magblock 15/30 MCL (Magazine Capacity Limiter) for CAA 30 round polymer magazines in .223/5.56mm. 

- This block will attach to the bottom of the spring, and sits on top of the original locking plate.
- Easy conversion of 30 round CAA magazines to hold 15 rounds.
- Does not affect reliability.
- No increase in spring pressure. 

Glock .45 Magblock 10 and 15 Round Limiter for 27 Round Magazines

- Fits 27 round Factory Glock .45 magazines and Korean manufacture magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 or 15 rounds of .45
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatable with the follower type and magazine base extension shown in the pictures. If yours is different then modifications may be needed.

** Select desired magazine capacity before adding to your cart.

Magblock 10 Round Limiter for Sig P226 (.40) 15 Round Magazines

- Fits 15 round .40 Sig P226 magazines made by Mec-Gar.  (13+2 extension)
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 10 Round Limiter for Sig P226 (.40) 13 Round Magazines

- Fits 13 round .40 Sig P226 magazines made by Mec-Gar. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
  *Universal Limiter can be used to make this block. Cut the base flush with #8 showing in the indicator notch. 

Springfield XD .40 Magblock 10 Round Limiter

• Fits 12 round XDM .40 magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of .40
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

10 Round Limiter for SWAMP FOX 30 Round Polymer Magazines

Magblock 10/30 MCL (Magazine Capacity Limiter) for Swamp Fox 30 round polymer magazines in .223/5.56mm. The Swamp Fox TMG-M30-P01 is a 30 round light weight polymer magazine that fits 5.56×45 NATO and .223 Remington AR15/M16 style firearms.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Customized base of the Magblock includes a locking point just like the original locking plate.
- Does not affect reliability.
- No increase in spring pressure. 
- Easy to install.  

Sig Sauer P226 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Sig P226 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/15 Sig Sauer P226 magazines. 
- No modification to the magazine is required.
-  Lightweight and will not interfere with magazine reliability.
- Tested on factory Sig P226 magazines as shown in the photos. The block may need to be modified to work with magazines from other manufactures. 

*This magazine is known to use two different types of followers depending on where they were manufactured. Please select the country of manufacture or your follower length below. The most accurate way is to measure your follower as shown in the photos. 

Beretta PX4 Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta PX4 13 round 9mm magazines and will limit them to 10 rounds.  Installs at tje base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired. 

- Quick install to make 10/13 Beretta PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 13 round Beretta PX4 magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Beretta 92 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Note: This block won't work in the newer Beretta M9A3 17 or Beretta 90-Two 17 round magazines. These magazines uses a different block. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Smith & Wesson 5900 Series Magblock 10/15 (9mm)

This Magblock fits the Smith & Wesson 5900 Series 15 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds under the magazine follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/15 S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

Troy BattleMag 15/30 MCL (Magazine Capacity Limiter) for 30 round Troy BattleMags in .223/5.56mm.

- This block will sit on top of the Troy locking plate and convert a 30 round magazine to hold only 15 rounds.

- The optional shock absorbing floor plate will still function normally.

- Does not affect reliability.

- No increase in spring pressure or wear. 

(Note: This is a custom trimmed Pmag block)