Magblocks

HK416 22LR 10/30 Magblock 10 Round Limiter

- This block will convert 30 round HK 416 22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

Mini 14 Magblock 10/20 MCL (Magazine Capacity Limiter for Ruger Magazines

 This block is for use in RUGER 20 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 20 round magazine to hold only 10 or 15 rounds. (Select option below). 

- Only for use in RUGER manufactured magazines. 

- This is a modified USGI magblock.

- This block will work in both the 5.56/223 and 300 Blackout Ruger Mini 14 magazine.

Magblock for ProMag DPMS LR-308 20 Round Magazines.  10 or 15 Round Limiters available.
Fits Promag DPMS LR-308 20 round magazines in .308/7.62x51mm and will convert them to hold only 10 or 15 rounds.

- Easy to install in seconds.
- No need to drill any holes.
- Load magazines on a closed bolt in most rifles.
- No external magazine modifications.

Magblock for ArmaLite AR10 25 Round Magazines.  10 and 15 Round Limiters.

Fits ArmaLite AR10  .308/7.62x51mm 25 round magazines and will convert them to hold only 10 or 15 rounds.

- Easy to install in seconds.
- No need to drill any holes.
- Load magazines on a closed bolt in most rifles.
- No external magazine modifications.
- Select 10 or 15 round limiter below. 

Smith & Wesson M&P 9 mm Compact Magblock 10 Round Limiter

- Fits 12 round 9mm M&P and M&P 2.0 Subcompact magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Sten 32 and 20 Round Magazines

- Fits Sten 32 round magazines and 32 round magazines that have been "Brass Wire" limited to 20 rounds. You must choose an option below.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.
- Please Note: The Photos show a 32 round magazine that has 2 brass wires on the inside that protrude outside near the bottom of the magazine. This is a Sten 32 round magazines that was limited to a single stack 20 round magazine. This was a common military modification that helped with reliability and very widespread on surplus magazines. Please select the "Single Stack Modified" option below if you see these brass wires at the bottom of your magazine to ensure you receive the proper limiter. Thank you.

FNS-9 and FNS-9 Compactg Magblock 10 and 15 Round Limiters

- Fits 17 round 9 mm Factory FNS-9 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 or 15 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block will only work in the magazines with the follower like in the photos.

Beretta 92 Magblock 10/30 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 30 round 9mm magazines and will limit them to 10 rounds.  Easily installed under the follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/30 Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round 6.8 mm "Six8" Pmags for LWRC.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- Includes a spacer for the proper height in the 6.8 mm magazine.

- Does not affect reliability.

- No increase in spring pressure. 

- *Compatible with Pmag 6.8 mm Magazines Only