Magblocks

Magblock 10 Round Limiter for CZ 75B Full Size 9mm 17 Round Magazines

- Fits 17 round 9mm CZ-75B and CZ-75 SP01 magazines as shown in the photos.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested on CZ-75 magazines made by Mec-Gar as shown in the photos. 

*If using our Universal Limiter for this magazine: Cut to #11 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. #11 will show in the limiter window notch like in the photos.  

Ruger SR40 10/15 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Ruger SR40 .40, 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger SR40 Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "12" showing in the indicator notch. Cement the base and slide together.

Magblock 10 Round Limiter for CZ 75 Compact and Subcompact 9mm 14 Round Magazines by Mec-Gar

- Fits 14 round 9mm CZ-75 compact and subcompact magazines as shown in the photos.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested on CZ-75 magazines made by Mec-Gar as shown in the photos. CZ brand factory magazines are listed as a different product.

*If using our Universal Limiter for this magazine: Cut to #6 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. #6 will show in the limiter window notch like in the photos.  

 Magblock 10 Round Limiter for Heckler & Koch USP, P30 and VP9 9mm

- Fits 15 round 9mm H&K USP, P30 and VP9 magazines. 
- Limits the magazinbe to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This block is made from our Universal Pistol Limiter and is cut so that the number "9" shows up in the indicator notch. The lock tab is not used and the slide is cut so that it is flush with the base of the limiter. The 2 pieces are then bonded together. See photos for details. 

Glock 19X Magblock 10/19 (9mm)

This Magblock fits the Glock 19X magazines with the +2 extended base. (19 round magazines)  and will limit them to 10 rounds.  

- This is a 2 part limiter. It is a -17 round limiter under the follower, then a -2 adapter to limit the extended floorplate.

- Easily installed in seconds. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/19 Glock 19X magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

PATENT # 9328982 B2, Additional Patents Pending

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 15 round 9mm M&P full size magazines. (Identified by extra spring coils at the base) 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 15 Round Magazines. 

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*Universal Pistol Limiter Instructions: Cut to #14 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #14 will show in the limiter window notch like in the photos.  

*This block will not work on M&P Compact 9mm magazines, and are only designed for Full-Size magazines.

Larger 6" Flush cut pliers make easy work of cutting through the Universal Limiters, Glock, XD/XDM, and Pmag limiters. Can cut universal limiters flush with the base, but may take a cut on each side to get through. 

 Magblock 10 Round Limiter for Heckler & Koch USP and P30 .40

 - Fits 13 round .40 H&K USP and P30 magazines. 
- Limits the magazinbe to 10 rounds of .40
- Easy installation at the base of the magazine. Sits on top of the locking plate as shown.
- Held in place with tension or can be epoxied in place.
- Lightweight, efficient design. 

FYI: The Universal Pistol Limiter cut to "6" in the indicator notch with a flush base works to limit this magazine to 10 rounds.

Beretta PX4 Full Size Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 15 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/15 Beretta Full Size PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 15 round Beretta PX4 magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for CZ P-07 Duty (9mm) 16 Round Magazines

- Fits 16 Round 9mm CZ P-07 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Patented Design 

*** Universal Pistol Limiter Instructions: Cut to "11" showing in the indicator notch and a flush base. (Ordering here is for pre-cut and finished blocks for a drop in limiter.)

Ruger Security 9 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Ruger Security 9, 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10 round Ruger Security 9 Magazines.

-No modification to the magazine is required. The spring bottom can fit into the drilled hole in the limiter or you can bend the spring if desired.

-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "9" showing in the indicator notch. Cement the base and slide together. Drill a hole to allow room for the spring as shown in the photos or just bend the spring straight at the bottom with pliers.

SCAR 17 MAGBLOCK

- New and Improved Easy Install Design.

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 10 round magazines to hold only 5 rounds, or a 20 round magazine to hold 15 rounds 

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

- Can also limit a 20 round Scar 17 magazine to 15 rounds.

- Made from super strong ABS plastic. 

Same as this item:  http://www.magazineblocks.com/magento/products/magblock-kits/scar-17/scar-17-magblock-15-20.html

*PATENT PENDING*

Magblock 10 Round Limiter for CZ-75, Shadow, Shadow 2  17 Round Magazines

- Fits 17 round 9mm CZ-75, CZ Shadow 2 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-This block works in the Shadow, Shadow2, and AccuShadow 2 17-round magazines.

*If using our Universal Limiter for this magazine: Cut to #11 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. #11 will show in the limiter window notch like in the photos.  

15 Round Limiter for Gen M3 30 Round Pmags

Magblock 15/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Gen M3 Pmags in .223/5.56mm. 

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 15 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed on many rifles.

- Does not affect reliability.

- No increase in spring pressure. 

- Compatable with new Magpul Gen 3 Pmags only.  These will not work in original Pmags.'

- Attention: We now offer the option to use our block with the Magpul factory retaining plate with our block. The block will sit on top of the Magpul retaining plate and is cut differently than our standard Gen M3 10/30 magblock. If you're planning on not using the factory retaining plate then we have an options for you.