Lancer L7 10/20 Limiter for 20 round magazines in .308/7.62x51mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 10 rounds.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear. 
Note: This is a custom modified Pmag block and will replace the original base. 

Magblock for Mossberg 590M 2 Round Limiter for 5 Round Magazines (12ga)

• Fits Mossberg 5 round magazines and will limit them to 2 rounds in the magazine for hunting. 
• Fits under the follower. The original plug will need to be removed by pulling out with pliers. See photos.
• Can be held in with included screw or epoxy if a permanent modification is needed. 

MAGBLOCK UNIVERSAL AK LIMITER KIT

ALLOWS FOR AN EASY CUSTOM SOLUTION FOR MOST METAL AK TYPE MAGAZINES. REQUIRES CUTTING OF THE MAGBLOCK FOR A CUSTOM FIT. AS SHIPPED IT WILL LIMIT MOST 30 ROUND MAGAZINES TO SLIGHTLY LESS THAN 10 ROUNDS.

Fits most steel 30 round AK47, AK74, AKS, SKS, VZ, and Saiga magazines and will convert them to hold only 10 or 15  rounds. Replaces the flat locking plates at the bottom of the spring. This part must be removed. Tested with Romanian, Russian, Korean, Promag, Saiga, IO, Chinese magazines and more.

- Features a spring catch which will allow an easy attachment point to the spring. This prevents the block making noise and epoxy can be added at this point to make it permanent.
- Pre notched cut outs in the most common lengths for easy cutting.
- Works on many military spec steel AK47 magazines.

Don't forget to check out our new upgrade stainless steel AK springs for polymer and steel magazines here or add below to your order. 

FNS-40 and FNX-40 Magblock 10 Round Limiter for 14 Round Magazines (.40)

- Fits 14 round FNX-40 and FNS-40 Factory magazines. 
- Save time and money with this simple part. 
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

FYI: The Universal limiter can also be used to make this block. Cut the universal limiter to #12 show in the indicator notch. 

Beretta 96 Magblock 10/12 (.40) 10 Round Limiter

This Magblock fits the factory Beretta 96 12 round magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/12 Beretta 96 magazines.
- Save time and money and keep your magazines legal. 
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 96 magazines as seen in the photos.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Pmag 21 GL9 Magblock 10 Round Limiter 10/21

This Magblock fits the Magpul Pmag 21 GL9 magazines used in 9mm Glocks and will limit them to 10 rounds. It is held in place with spring tension alone or can be glued or epoxied if desired.

• Simple install to make 10/21 Pmag 21 GL9 Glock magazines.
• Save Time and Money converting your magazines.
• No modification to the magazine is required.
• Lightweight and will not interfere with magazine reliability.
• Patented Design 

FNP-45 Magblock 10 Round Limiters

- Fits 15 round .45 Factory FNP-45 magazines. 
- Easy installation under the follower. Save time and money!
- Limits the magazine to 10 rounds of .45 and retains normal function.
- Held in place with spring tension or can be epoxied for a permanent modification where required by law.
- Lightweight, efficient design. 

Beretta 92 Compact Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 Compact 13 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 92 Compact magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 92 magazines as seen in the photos.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for Sig P365, P365X, 365XL, P365 Luxe 12 Round Magazines

- Fits 12 round 9mm Factory Sig P365, P365X and P365XL magazines. 
- Save time and money with a simple install.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification where required to be legal. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
-See installation video below 

 Magblock 10 Round Limiter for Heckler & Koch USP .45 

- Save time and money converting your magazines.
- Fits 12 round .45 H&K USP magazines. 
- Limits the magazinbe to 10 rounds of .45
- Easy installation at the base of the magazine. Sits on top of the locking plate as shown.
- Held in place with tension or can be epoxied in place.
- Lightweight, efficient design. 

FYI: The Universal Pistol Limiter cut to "3" in the indicator notch with a flush base works to limit this magazine to 10 rounds.

Beretta PX4 Compact Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Compact Beretta PX4 15 round 9mm magazines and will limit them to 10 rounds. Installs at the base of the spring. A notch allows room for the metal tab on the locking plate. It is held in place with spring tension alone or can be glued or epoxied if desired. (Compact magazines use a different limiter)

- Save time and your expensive factory magazines. Quick install to make 10/15 Beretta Compact PX4 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 15 round Beretta PX4 magazines and CX4 as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for Sig P226 ,12 Round .40 Magazines. 

- Fits the new 12 round .40 Factory Sig P226 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.
- Uses the Universal Limiter cut with #6 in the indicator notch with a flush base.

Ruger BX-15 Magblock 10 Round Limiters

- Fits 15 round 22LR Ruger BX15 magazines.
- Easy installation.
- Limits the magazine to 10 rounds of 22LR
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Walther .40 P99 Magblock 10 Round Limiters

- Fits 12 round .40 Factory Walther P99 magazines as shown.
- Easy installation under the follower as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.