Magblocks

Magblock 10 Round Limiter for Sig 550 / PE90 30 Round Magazines

- Fits 30 round 5.56mm Sig 550, PE90, SG 550 factory 30 round magazines.
- Easy installation. limiter replaces the original locking plate.
- Limits the magazine to 10 rounds of 5.56mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design. 
- Made of strong, lightweight polymer. 
 

 

Magblock 10 Round Limiter for Sig P320 (.40) 13 Round Magazines

- Fits 14 round .40 Sig P320 factory magazines.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

 FYI: Universal Limiter can be used to make this item. Cut limiter flush at the base with between 11-12 in the indicator notch. 

 

HK33 and C93

- This block will convert 20 round Promag HK magazines into a 10 round magazine.

- Works with Promag .223/5.56mm magazines.

- Replaces factory locking plate 

Smith & Wesson M&P22 (.22LR) Magblock 10 Round Limiter New Improved Fit

- Fits 12 round .22 M&P-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Kel-Tec PMR-30 22WMR 10/30 Magblock 10 or 15 Round Limiter

- This block will convert 30 round Kel-Tec PMR-30 22WMR magazines into a 10 or 15 round magazine.

- Easy to install without damage to your magazines.

Beretta 92, 92FS, M9A1 Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 92 15 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory "Made in Italy" Beretta 92 magazines as seen in the photos.

*** If you have M9 magazines made by Mec-Gar you must select the option below for a longer limiter. These magazines are marked "M9" on the side. 

NOTE: Multiple variations of this magazine may exist. Consider ordering the "Do not glue" option below.  Another option is the Universal Kit below which you can start with the block cut to around 12 and test the fit. Most need to be cut around 10, but the Universal Limiter gives you the option to custom fit to your magazine and tension on the last round. Order the Universal at this link:  http://www.magazineblocks.com/magento/magblock-universal-pistol-limiter.html

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock for Promag and some Bulgarian AK47 (7.62x39mm) Magazines.

- This block fits the Promag and Bulgarian (Plastic follower only) 30 round AK47 magazines in 7.62x39mm and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

- Note: This is a modified Tapco limiter so will be marked with Tapco markings. The cut down lines for other sizes are not accurate. Only for use with 30 round magazines.

Magblock 10/30 limiter for 5.45x39 mm AR Magazines only.

- Tested in C-Products and ACS magazines.
- These blocks will convert a 30 round 5.45x39 mm magazine to hold only 10 rounds.

Epoxy, Machinable Fast Setting.

Hardman Double Bubble Pouch (3.5 grams). Will work for a few rifle or up to 10 pistol limiters depending on amount used.
Features a longer working time than the Red fast set epoxy:
- Starts to set in 25 minutes, Handling time 4 hours. Mix small batches if doing a lot of limiters.
- Handling strength: 4 hours.
- Color: Aluminum.
- Viscosity: Honey.
- Full Strength: 24 hours

3.5 Grams.

Epoxy Fast Setting

Hardman Double Bubble Pouch (4.0 grams). Will work for a few rifle or up to 5-10 pistol limiters depending on amount used.
Features:
- Starts to set in only 3- 5 minutes. Mix small batches if doing a lot of limiters.
- Handling strength: 15-30 minutes.
- Color: white.
- Viscosity: honey.
- Full Strength: 24 hours

4.0 Grams.

This block fits 30 Round Thompson .45 magazines to limit them to 10 rounds.

The spring can also be epoxied to the block for a permanent installation. A spring catch at the bottom makes installation quick and easy.

This block will work with 32 round 9 mm UZI and MetalForm magazines to make a 30 round magazine. It replaces the lower floor plate. The spring can also be epoxied to the block which allows for disassembly and cleaning, or epoxy the floor plate closed for a more secure modification.

Magblock 10 Round Limiter for CZ-75 (.40) 14 Round Magazines

- Fits 14 round .40 CZ-75 SP-01 magazines using extended floor plate.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.
- Tested on CZ-75 magazines made by Mec-Gar as shown in the photos. Has also been reported to work with factory magazines. The block may need to be modified to work with magazines from other manufactures.

Magblock 10 Round Limiter for CZ-75 (.40) 12 Round Magazines

- Fits 12 round .40 CZ-75 SP-01 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of .40 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on CZ-75 magazines made by Mec-Gar as shown in the photos. Has also been reported to work with factory magazines. The block may need to be modified to work with magazines from other manufactures.
- *Same as P229 .40 10/12 limier