Magblocks

Genuine Factory Beretta 92FS Magblock 10/18 (9mm) 10 & 15 Round Limiter

This Magblock fits the factory Beretta 92FS Series 18 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta 92 Series magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92FS 18 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

 Attention: Make sure to verify what magazine you have before ordering. This block will fit the following 18-round 92FS series magazines Made By Beretta and not MecGar:

Beretta 90-two, Beretta 92G, Beretta M9, Beretta 92D, Beretta 92 Vertec, Beretta 92F, Beretta 92GTS

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

ETS Glock 9mm Magblock 10 Round Limiter for 32 round Magazines

This Magblock fits the ETS 32 round 9mm magazines for Glocks and will limit them to 10 rounds.  Easily installed under the follower of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/32 Glock 9mm magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

*This block is designed for the ETS 32 Glock magazines only. If used in other magazines it might need to be modified.

Promag FN Five-Seven Magblock 10 Round Limiter

- Fits 30 round 5.7 mm Promag FN magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

Magblock 10 Round Limiter for Brownells - Meccanica Del Sarca CZ-75 15 Round "Red Follower" Magazines

- Fits 15 round 9mm CZ75 Brownells magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #15 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #15 will show in the limiter window notch like in the photos.  

 ATTENTION:  This block is designed for the Brownells - Meccanica Del Sarca CZ-75 15 round magazines only. This block won't function correctly in factory or MecGar 15 round CZ-75 magazines. These magazines are sold by Brownells.com, and have a distinctive red follower that have a circler point under the follower piece (See: pictures for examples). 

Smith & Wesson M&P Shield Plus, Shield X and Equalizer 9mm Magblock 10 Round Limiter

- Fits 15 round 9mm M&P Equalizer, Shield Plus and Shield X magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- See video below for magazine disassembly instructions. 

Tippmann Arms M4-22 .22LR 10/22 Magblock 10 and 15 Round Limiter

- This block will convert 25 round Tippman Arms M4-22  .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne and allows you to use all factory parts of the magazine.

Lancer L5 5 Round Limiter For 20 Round 300 Blackout & 350 Legend Magazine

- This new design block will sit on top of the lower spring attachment point   or locking plate and convert a 20 round magazine to hold only 5 rounds.

- Only fits L5 Advanced Warfighter with slide on base. 

- Does not affect reliability.

- No increase in spring pressure or wear. 

- Uses a custom modified Pmag Block.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for AC-Unity MP5 9mm 30 Round Magazines

- Fits 30 round 9mm AC-Unity MP5 style magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

NOTE: This block is designed for the AC-Unity MP5 Magazines.
 

Taurus PT909 and PT809 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT909 and PT809 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Taurus PT909 and PT8099 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT909/PT809 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Magblock 10 Round Limiter for Century Arms, MKE OEM AP5 MP5 9mm 30 Round Magazines

- Fits 30 round 9mm Century Arms, MKE MP5 style magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

NOTE: This block is designed for the Century Arms OEM MP5 Magazines and the factory H&K MP5 magazines.

Ruger Security-380 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Ruger Security-380 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired. This block works inconjuntion with the factory spacer from Ruger. Please see pictures for details.

-Simple install to make 10 round Ruger Security .380 Magazines.

-No modification to the magazine is required. The spring bottom can fit into the drilled hole in the limiter or you can bend the spring if desired.

-Lightweight and will not interfere with magazine reliability.

Magblock 10 Round Limiter for KCI HK MP5, SP5, HK94 9mm 30 Round Magazines

- Fits 30 round 9mm KCI MP5 style magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

NOTE: This block is designed for the KCI MP5 and Zenith ZF-5 MP5 Stye magazines only. This block will not work in Factory HK MP5 magazines.

- This block will also work in the PTR 9R, 9KT, 9C, and 9CT-CL 30-round MP5 style magazines.

Palmetto State Armory Five-Seven Magblock 10 Round Limiter

- Fits 23 round 5.7 mm Factory PSA magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 5.7 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design.

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Limiter for STI Staccato CS and C 16 Round 9mm Magazines

- Fits 16 round 9mm Factory Staccato STI CS  magazines. 
- Easy installation into the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

Attention: Staccato has recently started offering the 16-round CS/C magazine with with a new spring and retaining plate. If you have them on your magazine, make sure to choose the correct option below. You will need a shorter block. See Pictures 

Type A Option: The spring is a silver color and the retaining plate doesn't have the raised cross inside of it.

Type B Option: The spring has a black tint to it and the retaining plate has a raised cross.