Magblocks

Magnum Research Baby Desert Eagle Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Magnum Research Baby Eagle magazines as shown.
- Tested in Magnum Research Baby Eagle 9mm 15 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

-This block is designed for the Magnum Research Baby Eagle 2 and Baby Eagle 3. Please review the pictures. Magnum Research makes 2 different Baby Eagle magazines (Please Review Pictures). 

Taurus G3 Magblock 10/17 and 15/17 (9mm) 10 and 15 Round Limiter

This Magblock fits the factory Taurus G3 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus G3 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all. 

Walther PDP Compact Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Walther PDP Compact magazines as shown.
- Tested in Walther PDP Compact Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit.

-This block will fit the new PDP-F magazines. 

Magblock 10/50 MCL (Magazine Capacity Limiter) for X-Products X-14 HXP 50 round Drum in 7.62x51/.308.

- Magazines can be loaded with the bolt closed.
- Does not affect reliability
- No increase in spring pressure
- Easy to install, see the video. 

Magblock 10 Round Limiter for Marlin Camp 9 (9mm) 12 Round Magazines

- Fits 12 round 9mm Marlin Camp 9 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. 

FN PS90 MAGBLOCK FACTORY 10/30 MAGAZINE

- New and Improved Easy Install Design.

- This block will fit original 5.7x28mm FN PS90 Magazines made by FNH and some aftermarket magazines as well.

- The block replaces the factory locking plate and will convert 30 round magazines to hold only 10 rounds. (No Need for Factory Block)

- No modifications to your expensive FN PS90 magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

*PATENT PENDING*

Taran Tactical +4 Extension Glock 17 and Glock 34 (9mm) Magblock

- Fits 21 round 9mm Glock 17 and Glock 34 Magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Nemo Arms Omen Magnum .300 Winchester Magnum Magblock 5/14

Fits Nemo Arms Omen Magnum 14 round magazines and will convert them to hold only 5 rounds for hunting.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

Taurus TX-22  (.22LR) Magblock 10 Round Limiter for 16 Round Magazine.

- Fits 16 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 *ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield XD 9mm 10/15 Round Magblock

• Fits 15 round XD and XD Mod 2 9mm magazines. 
• Easy installation at the base of the magazine.
• Limits the magazine to 10 rounds of 9mm.
• Can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

*This block is designed for the factory 15 round magazine, made by Springfield. Will not work on Promag XD magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

- Fits Gen1 and Gen 2 Pmag 15 only.

Beretta PX4 Full Size Tactical Magblock 10/17 (.40) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round .40 caliber magazines and will limit them to 10 rounds. Installs at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired. (This block is for the tactical version magazine).

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines in .40S&W.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 (.40) magazines as seen in the photos. 

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

PROMAG Ruger Mini 30 Magblock 10/30 Magazine Capacity Limiter

 This block is for use in PROMAG RUGER 30 round Mini 30 magazines. These blocks will insert at the base of the magazine spring and convert a 20 round magazine to hold only 10 rounds.

- Only for use in PROMAG manufactured magazines. 

- Designed to work in the polymer magazine only.