Accuracy International .300 Norma Mag - .338Lupa Mag Magblock 5/10 Limiter

- For use in Accuracy International 10 round magazines as pictured.

- These blocks will convert a 10 round magazine to hold only 5 rounds.

 

Magblock 10 & 15 Round Limiter for Palmetto PSA AK-V, AR-V 9mm 35 Round magazine

- This block fits the new Palmetto PSA AK-V and AR-V 9mm magazines and will convert them to hold 10 and 15 rounds.

-Installs at the base and is held in place by spring tension.

- Made of super strong heat resistant polymer.

-This block is compatiable with the Palmetto PSA AK-V U9 35 round magazines.

Heckler & Koch G36 Magblock

- Works with Factory Magazines for the HK G36 only.

- 10/30 and 15/30 configuration (10 rounds in a 30 round body)

- Simple quick install. 

Smith & Wesson 5900 Series Magblock 10/14 (9mm)

This Magblock fits the Smith & Wesson 5900 Series 14 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds under the magazine follower. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/15 S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

-Block is designed for the 14 round, black follower, early version, 659 series magazines. 

Magblock 10 Round Limiter for Eagle Import SPS 21 Round 9mm/.38 Magazines

- Fits 21 round 9mm/38super Factory Eagle Import SPS magazines. 
- Easy installation into the follower.
- Limits the magazine to 10 rounds of 9mm/38super. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

Magblock 10 and 15 Round Limiter for Steyr SPP 30 Round Magazines

- Fits 30 round 9mm Steyr SPP factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Magblock 10 and 15 Round Limiter for Steyr L9-A2 17 Round Magazines

- Fits 17 round 9mm Steyr A2-MF factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #17 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. 

HK270 22LR 5/20 Magblock 5 Round Limiter for Hunting

- This block will convert 20 round HK 270 22LR magazines into a 5 round magazine for Hunting.

- Easy to install without damage to your magazines.

-Block will replace the factory locking plate.

 

HK270 22LR 10/20 Magblock 10 and 15 Round Limiter

- This block will convert 20 round HK 270 22LR magazines into a 10 and 15 round magazine.

- Easy to install without damage to your magazines.

-Block will replace the factory locking plate.

 

Magblock 10 and 15 Round Limiter for EAA Girsan MC28 17 Round Magazines

- Fits 17 round 9mm EAA Girsan MC28 factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #11.5 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #11 with the top part of #12 will show in the limiter window notch like in the photos.  

Magblock for Panzer Arms MKA1919 AR-12 5 Round Limiter for 10 Round Magazines (12ga)

• Fits Panzer Arms 10 round magazines and will limit them to 5 rounds. 
• Fits at the base of the magazine. This block will replace the factory locking plate.

Magblock for Rock Island Armory 5 Round Limiter for 9 Round Magazines (12ga)

• Fits Rock Island Armory VR60 9 round magazines and will limit them to 5 rounds. 
• Fits at the base of the magazine. This block will replace the factory locking plate.

Glock 23 (9mm) Magblock (For Older Style Followers Only)

- Fits 13 round .40 Foctory Glock 23 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits older style follower Glock Magazines only.
Only compatable with the follower type shown in the pictures. 

Magblock 10 Round Limiter for MecGar Para Ordnance P14 .45 magazines

- Fits 14 round .45 MecGar Para Ordnance P14 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on MecGar Para Ordnance P14 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

WILL NOT WORK WITH PRO-MAG PARA14 MAGAZINES

H&K Promag USC .45 Magazine Magblock 10/15 Limiter

- For use in H&K Promag USC .45 15 round polymer magazines as pictured.

- These blocks will convert a 15 round magazine to hold only 10 rounds.

 

PIONEER ARMS AK47 (7.62x39mm) Magazines.

- This block fits the 30 round AK47 magazines in 7.62x39mm made by Pioneer Arms and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

-This block installs at the base.

Magblock for Zastava Z-Mag Polymer ZPAP85 AK74 (5.56x45) Magazines.

- This block fits the Zastava ZPAP85 30 round AK47 magazines in 5.56x45 and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

Want to upgrade to the best stainless steel AK replacement springs available? See our upgrade springs here: LINK

Ruger BX-15 Magblock 5 Round Limiters for .22WMR & .17HMR for hunting.

- Fits 15 round .22WMR & .17HMR Ruger BX15 magazines.
- Easy installation.
- Limits the magazine to 5 rounds of .22WMR & .17HMR
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Magblock 10 Round Limiter for CZ-75 Compact, P-01, and PCR 15 Round Magazines

- Fits 15 round 9mm CZ75 Compact, P-01, and PCR  factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #8 and glue flush at the bottom for 10/15 limiter. 

*Tested on factory CZ75 Compact 15 round magazine that are marked 11rd .40 on the other side. This block will fit the new Shadow 2 Compact magazines.

Magblock 10/20 and 15/20 Okay Surefeed USGI MCL (Magazine Capacity Limiter)

- For use in Surefeed Okay Industries 20 round magazines.
- These blocks will convert a 20 round magazine to hold only 10 rounds.

-Note: This block is designed for the OKAY Industries Surefeed 20 round magazine only. It will not work in other USGI 20 round magazines without modification. 

Magblock 10 Round Limiter for CZ-82, CZ-83 (.380 and 9x18) 12 Round Magazines

- Fits 12 round .380, 9x18 CZ-82, CZ-83 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of .380 and 9x18.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on CZ55 - CZ-82, CZ-83 factory magazines

Taurus GX4 Magblock 10/11 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus GX4 11 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus GX4 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

 

 

Fits Browning BAR .30-06 20 round magazines.

- Easiest and quickest way to make a 5 round Browning BAR Magazine perfect for hunting.

- Can be permanently attached to the spring with epoxy.

- The block attaches to the spring to prevent noise and movement.

- No magazine modifications required.

-Allows loading on a closed bolt with 10 rounds installed.

-New light weight design.

Fits Browning BAR .30-06 20 round magazines.

- Easiest and quickest way to make a 10 round Browning BAR Magazine.

- Can be permanently attached to the spring with epoxy.

- The block attaches to the spring to prevent noise and movement.

- No magazine modifications required.

-Allows loading on a closed bolt with 10 rounds installed.

-New light weight design.

PROMAG Ruger Mini 30 Magblock 10/30 Magazine Capacity Limiter

 This block is for use in PROMAG RUGER 30 round Mini 30 magazines. These blocks will insert at the base of the magazine spring and convert a 20 round magazine to hold only 10 rounds.

- Only for use in PROMAG manufactured magazines. 

- Designed to work in the polymer magazine only.

ProMag M14/M1A 7.62x51mm/.308 20 round magazines.

- Easiest and quickest way to make a 10 round M14 Promag (Only) Magazine.

- Can be permanently attached to the spring with epoxy.

- The block attaches to the spring to prevent noise and movement.

- No magazine modifications required.

-Allows loading on a closed bolt with 10 rounds installed.

-New light weight design.

-This block is designed for the PROMAG M14/M1A 20 Round magazine, only. Military surplus and other manufacturers use our standard block.

Walther PDP Compact Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Walther PDP Compact magazines as shown.
- Tested in Walther PDP Compact Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit.

-This block will fit the new PDP-F magazines. 

Beretta 90-Two Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta 90-Two 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta 90-Two magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 90-two magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

-Will not work on older Beretta 92 17 round magazines. Will only work on Beretta magazines pictured below.

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 Attention: Make sure to verify what magazine you have before ordering. The magazine you have should look like the one in the picture. 

Taurus G3 Magblock 10/17 and 15/17 (9mm) 10 and 15 Round Limiter

This Magblock fits the factory Taurus G3 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus G3 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

 

Smith & Wesson M&P Shield Plus, Equalizer 9mm Sub-Compact Magblock 10 Round Limiter

- Fits 13 round 9mm M&P Shield Plus magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Pmag LR10 Magblock GEN M3 Magazine Capacity Limiters (5 Round for Hunting)

Fits the Magpul LR10 .308/7.62x51mm 10 round Pmags and will convert them to hold only 5 rounds for hunting. 

- Will NOT fit older version magazines. Gen M3 Only.

- Load magazines on a closed bolt in most rifles.

- Easy to install. New style block allows you to use the stock locking plate.

- No external magazine modifications.

GSG-15 .22LR 10/22 Magblock 10 and 15 Round Limiter

- This block will convert 22 round GSG-15 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne.

GSG AK-47 .22LR 10/24 Magblock 10 and 15 Round Limiter

- This block will convert 22 round GSG .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne.

Beretta PX4 Full Size Tactical Magblock 10/17 (.40) 10 Round Limiter

This Magblock fits the factory Full Size Beretta PX4 17 round .40 caliber magazines and will limit them to 10 rounds. Installs at the base of the spring.  It is held in place with spring tension alone or can be glued or epoxied if desired. (This block is for the tactical version magazine).

- Save time and your expensive factory magazines. Quick install to make 10/17 Beretta Full Size PX4 magazines in .40S&W.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory 17 round Beretta PX4 (.40) magazines as seen in the photos. 

*Universal Instructions: Cut Universal limiter to #19 in the indicator notch. A cutout in the limiter base is needed or the slide lock can be used. See photos for details. 

- Fits Gen1 and Gen 2 Pmag 15 only.

Springfield Hellcat 9mm 10/15 Magblock

- Fits 15 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Note: Please verify which number is showing under the follower of your magazine. If the number reads #4 or #3 then you'll need a special cut Hellcat block. If it reads any other number, then you can use the standard cut block.

Armscor/RIA XT-22 Magnum  (.22WMR) Magblock 10 Round Limiter for 14 Round Magazine.

- Fits 14 round Armscor/Rock Island Armory XT-22 magnum magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22magnum
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Magblock 10/50 MCL (Magazine Capacity Limiter) for X-Products X-14 HXP 50 round Drum in 7.62x51/.308.

- Magazines can be loaded with the bolt closed.
- Does not affect reliability
- No increase in spring pressure
- Easy to install, see the video. 

 

Magblock 10 Round Limiter for Marlin Camp 9 (9mm) 12 Round Magazines

- Fits 12 round 9mm Marlin Camp 9 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. 

FN PS90 MAGBLOCK FACTORY 10/30 MAGAZINE

- New and Improved Easy Install Design.

- This block will fit original 5.7x28mm FN PS90 Magazines made by FNH and some aftermarket magazines as well.

- The block replaces the factory locking plate and will convert 30 round magazines to hold only 10 rounds. (No Need for Factory Block)

- No modifications to your expensive FN PS90 magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

*PATENT PENDING*

 

Taran Tactical +3 Extension Glock 17 and Glock 34 (9mm) Magblock

- Fits 20 round 9mm Glock 17 and Glock 34 Magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

Nemo Arms Omen Magnum .300 Winchester Magnum Magblock 5/14

Fits Nemo Arms Omen Magnum 14 round magazines and will convert them to hold only 5 rounds for hunting.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

 

Taurus TX-22  (.22LR) Magblock 10 Round Limiter for 16 Round Magazine.

- Fits 16 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Springfield XD 9mm 10/15 Round Magblock

• Fits 15 round XD and XD Mod 2 9mm magazines. 
• Easy installation at the base of the magazine.
• Limits the magazine to 10 rounds of 9mm.
• Can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

*This block is designed for the factory 15 round magazine, made by Springfield. Will not work on Promag XD magazines.

Tanfoglio Stock Master Magblock 10/17 Round and 15/17 Round Limiter for 17 Round Magazines

This Magblock fits the Tanfoglio Stock Master 9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Tanfoglio Stock Master and  Italia Defiant Stock Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

"Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "18" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

*This block is designed for the Tanfoglio Stock Master Factory magazine (ONLY), and will not work on Mec-Gar magazines. 

Magblock for Catamount Fury 2 Round Limiter for 5 Round Magazines (12ga)

• Fits Catamount Fury 5 round magazines and will limit them to 2 rounds. 
• Fits at the base of the magazine. This block will replace the factory locking plate.

Mossberg MC2C 9mm Compact Magblock 10 Round Limiter for 15 Round Magazine

- Fits 15 round 9mm Mossberg MC2C magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Magblock 10 Round Limiter for Bul Armory SASII 2011 120mm 14 Round 45acp Magazines

- Fits 14 round 45acp Factory Bul Armory SASII 120 mm magazines. 
- Easy installation at the base of the magazine. (See pictures for details)
- Limits the magazine to 10 rounds of 45acp. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

Magblock 10 Round Limiter for Bul Armory SASII 2011 120mm 19 Round 9mm Magazines

- Fits 19 round 9mm Factory Bul Armory SASII 120 mm magazines. 
- Easy installation at the base of the magazine. (See pictures for details)
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

 Magblock 10 Round Limiter for Heckler & Koch P30 and VP9 9mm 15 round magazine that has a +5 HK store extension

- Fits 15 round to 20 round 9mm H&K P30 and VP9 magazines that has the +5 extension.
- Limits the magazine to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

 

 

FN 502 (.22LR) Magblock 10 Round Limiter for 15 Round Magazine.

- Fits 15 round FN 502 magazines. 
- Easy installation and allows you to use the stock locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Magblock 10 Round Limiter for Sig MPX 9mm 35 Round Magazines

- Fits 35 round 9mm Sig MPX factory magazines.
- Easy installation by inserting the block at the base. This block replaces the factory locking plate.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

New Magblock 10 Round Limiter for Sig P320 30 Round Magazines

- Fits 30 round 9mm Factory Sig P320 amagazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 Magblock 10 Round Limiter for Heckler & Koch P7M13 9mm

- Fits 13 round 9mm H&K P7M13 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation under the follower as shown in the photos.
- Lightweight, efficient design. 

-This block will work in P7M10 .40S&W marked magazines.

Walther WMP (.22 Magnum) Magblock 5 Round Limiter for 15 Round Magazine For Hunting

- Fits 15 round .22 Walther WMP .22 magazines. 
- Easy installation by using the stock locking plate. See photos.
- Limits the magazine to 5 rounds of .22 Magnun.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Magblock 10 Round Limiter for Kimber Mako R7 (9mm) 11 Round Magazines

- Fits 11 round 9mm magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Kimber Mako R7 11 round magazine.

Sig Sauer P320 X-Ten 10mm Magblock 10 Round Limiters for 15 Round Magazine

- Fits 15 round 10mm Sig P320 X-Ten 10mm magazines. 
- Limits the magazine to 10 rounds of 10mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory Sig Sauer X-Ten 10mm 15 round magazine

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

 This block will for for the new X-Ten Compact too

PufGun AK-74 Vepr .223 Magblock for 5.45x45mm 30 round magazines

• This AK-74 Vepr block fits 30 round polymer PufGun marked 5.45x45 mm magazines and will convert them to hold only 10 rounds.
• This prevents the block making noise and epoxy can be added at this point to make it permanent.

 

IMPORTANT:  This block is designed for the AK Vepr .223 marked PufGun magazines only. The block has a special adapter fixed to the bottom of the block,

so that you can use the stock locking plate with no issues. These blocks are designed to fit the PufGun Russian made magazines only.

 

 

Mossberg MC2C 9mm Sub-Compact Magblock 10 Round Limiter for 13 Round Magazine

- Fits 13 round 9mm Mossberg MC2C magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Magblock 10 Round Limiter for Sig P365 XMacro 17 Round Magazines

- Fits 17 round 9mm Factory Sig P365XMacro magazines. 
- Save time and money with a simple install.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification where required to be legal. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer. 

-This block will works in the X-Macro, Tacops, and P365-AXG Legion 17-round magazines.

 

Springfield XDM Elite 10mm Magblock 10 Round Limiter

• Fits 16 round XDM Elite 10mm magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of 10mm
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 
• NOTE: (Same limiter as the XDM 9mm 10/19, just cut down)

Glock 20, 40 (10 mm) Magblock Michigan Hunting

- Fits 15 round 10 mm Glock 20 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 8 rounds of 10mm ammunition for hunting in Michigan. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatable with the follower type shown in the pictures. 

Patent Pending

-This block is design to limit stock 15 round magazines to 8 rounds for hunting in Michigan.

Glock Pistol Limiter 3 Pack Kit

Save time and money by making your magazines legal. 

- This Glock Magblock fits most magazines from .Glock 17, Glock 34 (Without Cutting), Glock 22, Glock 35, Glock 19, Glock 23, Glock 20, Glock 41, Glock 19x (17rd magazine only).

- Easily installs into the follower (Only for Use in Gen3, Gen4 and Gen5 Magazines) . It is held in place with spring tension alone or can be epoxied if desired.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

 

Attention: Checkout the discounted items we offer to complete your magblock build.

Magblock for Zastava Arms PAP M77 .308 20 Round Magazines.  5, 10 and 15 Round Limiters.

Fits Zastava M77 .308/7.62x51mm 20 round magazines made by Zastava Arms.

- Easy to install in seconds.
- Allows the use of the stock locking plate.
- No external magazine modifications.
- Select 5, 10 or 15 round limiter below. 

- Tested in Zastava Arms M77 PAP magazines made by Zastava. 

Sig Sauer 1911 (.22LR) Magblock 10 Round Limiter 

- Fits 12 round .22 Sig Sauer 1911 magazines. 
- Easy installation. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Glock 26 Magblock 10/12 (9mm)

This Magblock fits the Glock 26 magazines with the +2 extended base. (12 round magazines)  and will limit them to 10 rounds.  

-Simple install to make 10/12 Glock 26 magazines w/ +2 extension.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

PATENT # 9328982 B2, Additional Patents Pending

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

 

 

Korean AK-74 Magblock for 5.45x39mm 30 round magazines

• This AK-74 block fits Korean 30 round metal 5.45x39 mm magazines and will convert them to hold only 10 rounds. Will only work on magazines with locking plate in picture.
• The new design features a spring catch which will allow an easy attachment point to the spring.
• This prevents the block making noise and epoxy can be added at this point to make it permanent.

 

Magblock 10 Round Limiter for Kimber Mako R7 (9mm) 13 Round Magazines

- Fits 13 round 9mm magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Kimber Mako R7 13 round magazine.

Walther WMP (.22Magnum) Magblock 10 Round Limiter for 15 Round Magazine

- Fits 15 round .22 Walther WMP .22 magazines. 
- Easy installation by using the stock locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Magblock 10 Round Limiter for Ruger Max 9 (9mm) 12 Round Magazines

- Fits 12 round 9mm magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Ruger Max 9. 

Magblock 10 Round Limiter for Ruger LCP Max (.380 ) 12 Round Magazines

- Fits 12 round .380 magazines
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of .380.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Ruger LCP Max 

Smith & Wesson M&P 2.0 10mm Magblock 10 Round Limiters

- Fits 15 round 10mm M&P magazines. 
- Limits the magazine to 10 rounds of 10mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W Magazines M&P 10mm

-This block will fit standard, 2.0, and Performace Center 15-round 10mm magazines

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

 

Springfield OSP Elite 10mm 10/11 Magblock

- Fits 11 round OSP Elite 10mm magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

AREX Rex Zero S1 Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory AREX Rex Zero S1 magazines as shown.
- Tested in AREX Rex Zero S1 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 16 shown in the indicator notch. Cement together after testing fit. 

Note: This block has only been tested with magazine that has the spring bunch at the bottom.

Magblock 10 Round Limiter for CZ Scorpion (.32) 20 Round Magazines

- Fits 20 round .32auto CZ Scorpion magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .32auto. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

 

 -This block will only work in the ,32 auto, 20 round magazine.

HERA ARMS H2 Magblock 10/20  (Magazine Capacity Limiter) for AR15/M16 Magazines

- For use in Hera Arms H2 AR-15 type 20 round magazines for the AR15/M16. 
- These blocks will convert a 20 round magazine to hold only 10 rounds.

 

 

 

Beretta M9-22, 92FS-22, M9A1-22 (.22LR) Magblock 5 Round Limiter New Improved Fit

- Fits 15 round .22 Beretta 92-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 5 rounds of .22 for hunting. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

Magblock for Black Ace Tactical 2 Round Limiter for 5 Round Magazines (12ga)

• Fits Black Ace Tactical 5 round magazines and will limit them to 2 rounds. 
• Fits at the base of the magazine. This allows you to use the factory locking plate.

Thermold Mini 30 Magblock 10/26 Magazine Capacity Limiter

 This block is for use in Thermold 26 round Mini 30 magazines. These blocks will insert at the base of the magazine spring and convert a 26 round magazine to hold only 10 rounds.

- Only for use in Thermold manufactured magazines. 

- Designed to work in the polymer magazine only.

Ruger PC Carbine 10/17 Magblock 10 Round Limiter for 17 Round Magazines

This Magblock fits the Ruger PC Carbine 9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger PC Carbine Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "12" showing in the indicator notch. Needs a hole drilled in the block to allow for the bend in the spring. See photos. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

Smith & Wesson CSX 9mm Magblock 10 Round Limiters

- Fits 12 round 9mm CSX magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 12 Round CSX Magazines. 

Sig Sauer P322 .22LR 10/20 Magblock 10 Round Limiter

- This block will convert 20 round Sig P322 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne. 

Magblock 10 Round Limiter for B&T 30 Round Magazines

- Fits 30 round 9mm B&T factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 -Block will work in B&T TP9, APC9, MP9, and GHM9 30-round magazines.

10 Round Limiter for Mod2 20 Round Amend2 Magazines

Magblock 10/20 MCL (Magazine Capacity Limiter) for Amend2 20 round in .223/5.56mm. 

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 10 rounds.

- Does not affect reliability.

- No increase in spring pressure. 

 -A custom made adaptor allowes for use of the stock floor plate. 

Taurus GX4 Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus GX4 13 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your factory Taurus GX4 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on original factory magazines.

 

 

Magblock 10 Round Limiter for Promag Canik TP9 18 Round Magazines (ONLY)

- Fits 18 round 9mm Promag Canik TP9 magazines (This Block Will Not Work In Factory Canik TP9 Magazines). 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on Promag (Only) Canik TP9 magazines. The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #20 showing in the notch to make this limiter. 

Mauser MP40 GSG .22LR 10/22 Magblock 10 Round Limiter

- This block will convert 22 round GSG .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne. You will not use the stock locking plate with this block.

KEL-TEC P50 MAGBLOCK 10/50 MAGAZINE

- New and Improved Easy Install Design.

- This block will fit original 5.7x28mm Kel-Tec P50 Magazines made by Kel-Tec.

- The block replaces the factory locking plate and will convert 50 round magazines to hold only 10 rounds. 

- The block can be epoxied to the spring for a permanent modification.

*PATENT PENDING*

 

 Magblock 10 Round Limiter for Heckler & Koch VP70 9mm

- Fits 18 round 9mm H&K VP9 magazines. 
- Limits the magazine to 10 rounds of 9 mm
- Easy installation under the follower as shown in the photos.
- Lightweight, efficient design. 

Magblock for Bulgarian AK-47 40 Round (7.62x39mm) Magazines.

- This block fits the Bulgarian 40 round magazines in 7.62x39mm and will convert them to a 10 rounds. 

- Replaces the lower locking plate for an easy and secure install.

.

Hexmag AR-10/SR25 Magblock 5/20

- Magblock 5/20 MCL block for use in polymer Hexmag AR-10/SR25 magazines.

- This block will convert a 7.62x51/.308 20 round magazine to hold only 5 rounds. 

- Uses the original Hexmag locking plates.

This block fits 20 Round Thompson .45 magazines to limit them to 10 rounds.

The spring can also be epoxied to the block for a permanent installation. A spring catch at the bottom makes installation quick and easy.

Magblock for Bakelite AK47 (7.62x39mm) Magazines (Hunting)

- This block fits the Bakelite 30 round AK47 magazines in 7.62x39mm and will convert them to a 5 round magazine.

- Replaces the lower locking plate for an easy and secure install.

Want to upgrade to the best stainless steel AK replacement springs available? See our upgrade springs here: LINK

ETS Glock 22 (.40) Magblock

- Fits 16 round .40 ETS Glock 22 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .40 ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 ATTENTION: This block is designed for the ETS Glock 22 magazine only. 

ETS Glock .40 Magblock 10 Round Limiter for 19 round Magazines

This Magblock fits the ETS 19 round .40 magazines for Glocks and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired for a permanent modification where required. (Epoxy sold separately). 

- Simple install to make 10/19 Glock .40 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Fits ETS magazines like the one pictured.

 *This block is designed for the ETS Glock .40 19 round magazine only. If used in other magazines it might need to be modified. 

Heckler & Koch UMP 9mm Magblock 10/30

- Works with H&K UMP 9mm 30 rd Magazines as shown.

-Uses the factory locking plate.

- Simple quick installation.

 

-Tested on USA made UMP 9mm 30 round magazines.

Magblock 10 Round Limiter for Sig Sauer 2022 SigPro 9mm 17 Round Magazines. Fits 2022 and 2009

- Fits 17 round 9mm Factory Sig Pro magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

The Universal limiter can be used to make this block by cutting flush with the base with #20 showing in the indicator notch. The blocks sold here are pre-cut and fixed at this length. 

SAR-9 Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory Sarsilmaz SAR-9 magazines as shown.
- Tested in SAR9 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 14 shown in the indicator notch. Cement together after testing fit. 

 Magblock 10 Round Limiter for Heckler & Koch USP 9mm Tactical

- Fits 31 round 9mm H&K USP9 Tactical magazines. 
- Limits the magazinbe to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

 

 

ETS Glock 20 (10 mm) Magblock

- Fits 15 round 10 mm ETS Glock 20 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 10mm ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

This block will work with 20 round 9mm Grand Power Stribog magazines to make a 10 round magazine. Block allows you to use the stock locking plate.

This block will work with 30 round 9mm Grand Power Stribog magazines to make a 10 round magazine. Block allows you to use the stock locking plate.

Magblock 10 Round Limiter for Grand Power K100 20 Round Magazines

- Fits 20 round 9mm Factory Grand Power K100 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #20 showing in the notch to make this limiter. 

Magblock Universal Pistol Limiter 3 Pack Kit
Allows for an easy custom solution for most standard pistol magazines. Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds.

Save time and money by making your magazines legal. 

NOTE: These are recommended for gunsmiths and hobbyists who don't mind experimenting with the length to get the fit they want. We do offer these as an option for some magazines already precut.  Now you have an option if we do not have a limiter available for your specific magazine with the recent law changes. If they don't work out for you just send them back for a refund or exchange.

- This Magblock fits most magazines from .380, 9mm, .40, 10mm and .45 magazines.

- Comes with one universal base, an adjustable slide, and a bottom lock plate which is optional to use. Highly recommend using optional Magblock Cement below.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Patented adjustment mechanism and end profile that prevents the limiter from sliding off the follower.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for a custom fit. As shipped it will limit most magazines to much less than 10 rounds. 

Refrence page. Lengths for tested magazines: http://www.magazineblocks.com/universal

Smith & Wesson SD40 VE .40 Magblock 10 Round Limiters

- Fits 15 round .40 SD40VE, SD40G, SD40E, SD40P, SD40V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40 cal. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 15 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #12 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #12 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

FNX-9 Magblock 10 and 15 Round Limiters

- Fits 17 round 9 mm Factory FNX-9 magazines. 
- Easy installation under the follower.
- Limits the magazine to 10 or 15 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Smith & Wesson SD9 VE 9mm Magblock 10 Round Limiters

- Fits 17 round 9mm SD9VE, SD9G, SD9E, SD9P, SD9V and SIGMA magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 17 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #16 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

IWI MecGar Jericho 941 Magblock 10 Round Limiter

- Fits 16 round 9 mm Made in Italy MecGar IWI Jericho magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block fits both 16 Round and 17 Round IWI Jericho 941 "Made in Italy" magazines. Tested on the magazine in the photos.  

 

IWI MASADA Magblock 10 Round Limiter

- Fits 17 round 9 mm Made in Italy IWI MASADA magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Taurus PT1911 Magblock 5/8 (.45) 5 Round Limiter for Hunting

This Magblock fits the factory Taurus PT1911 8 round .45acp magazines and will limit them to 5 rounds for hunting. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 5/8 Taurus PT1911 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT1911 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Smith & Wesson SW99 9mm Magblock 10 Round Limiters

- Fits 16 round 9mm SW99 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W SW99 16 Round Magazines. 

*Universal Pistol Limiter Instructions: Cut to #16 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  

Magblock 10 Round Limiter for Grand Power K100 P1 15 Round Magazines

- Fits 15 round 9mm Factory Grand Power K100 P1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power K100 P1 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #10 showing in the notch to make this limiter. 

AK-74 Bulgarian Magblock for 5.45x39mm 30 round magazines

• This AK-74 block fits most 30 round Bulgarian 5.45x39 mm magazines and will convert them to hold only 10 rounds.
• The new design features a spring catch which will allow an easy attachment point to the spring.
• This prevents the block making noise and epoxy can be added at this point to make it permanent.
• This block will replace the original magazine locking plate.

 

Tanker AK47 10/20 Magblock

This block fits the Tanker 20 round AK47 magazines and will convert them to a 10 round magazine.

-Replaces the lower locking plate.

-Works on Korean surplus magazines.

Taurus PT24/7 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT24/7 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Taurus PT24/7 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT24/7 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

ETS Smith & Wesson M&P Full Size 9mm Magblock 10 Round Limiters

- Fits 21 round 9mm ETS M&P magazines. 
- New design installs into the follower like in the pictures.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with ETS S&W 21 round Magazines.

 

Beretta APX Compact Magblock 10/13 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta APX Compact 13 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta APX Compact magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX Compact magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #4.5 and glue flush at the bottom for 10/13 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #4.5 will show in the limiter window notch like in the photos. 

Beretta APX Magblock 10/18 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 18 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #20 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #20 will show in the limiter window notch like in the photos. 

 Wilson Combat EDC X9 Magblock 10 Round Limiters for 18 Round Magazine

- Fits 18 round 9mm Factory Wilson Combact EDC X9 magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

Magblock 10 Round Limiter for Remington 1911 R1 9mm magazines

- Fits 19 round 9mm Remington 1911R1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

 

Magblock 10 Round Limiter for STI Staccato 126mm 17 Round 9mm Magazines

- Fits 17 round 9mm Factory Staccato STI P, XC, XL 126 mm magazines. 
- Easy installation into the follower of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

*Note: If you have a newer Staccato STI magazine that has G3 on the back of the magazine, then you will need to click G3 option below.

AREX Rex Delta Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory AREX Rex Delta magazines as shown.
- Tested in AREX Rex Delta 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 18 shown in the indicator notch. Cement together after testing fit. 

Archon Type B Magblock 10 Round Limiters

- Fits 15 round 9mm Archon Type B magazines as shown.
- Tested in Archon Type B 15 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number "12" shown in the indicator notch. Cement together after testing fit. 

Magblock 10 Round Limiter for FMK 9mm 14 Round Magazines 

- Fits 14 round 9mm FMK 9C1 magazines as shown in the photos.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested on FMK factory magazines. 

*If using our Universal Limiter for this magazine: Cut to #10 with side of base sanded and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. #10 will show in the limiter window notch like in the photos.  

Arsenal Circle 10 AK-74 Magblock for 5.45x39mm 45 round magazines

• This AK-74 block and adapter fits most 45 round polymer 5.45x39 mm magazines and will convert them to hold only 10 rounds.
• The new design features a spring catch which will allow an easy attachment point to the spring.
• This prevents the block making noise and epoxy can be added at this point to make it permanent.
• This block will replace the original magazine locking plate.

 

Magblock 10 Round Limiter for CZ-75 P07 16 Round Magazines

- Fits 16 round 9mm CZ75 P-07 factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #11.5 and glue flush at the bottom for 10/16 limiter. Slide lock is not used. When epoxy cures assemble magazine. #11.5 with the top part of #11.5 will show in the limiter window notch like in the photos.  

Beretta APX Magblock 10/15 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 15 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #9 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #9 will show in the limiter window notch like in the photos. 

 Wilson Combat EDC X9S Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Wilson Combact EDC X9S magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

Beretta ARX160 22LR 10/30 Magblock 10 Round Limiter

- This block will convert 30 round Beretta ARX160 22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

Universal AK47 10/30 Magblock

*** See our NEW Universal AK Limiter Here: CLICK HERE for the  IMPROVED UNIVERSAL AK KIT***

Fits most steel 30 round AK47 magazines and will convert them to hold only 10 rounds. Works best in magazines with flat locking plates like in the first photo. These tend to be Romanian, Russian, and Chinese magazines. Other plates may need to be modified to work correctly demonstrated in the second photo. This is encountered with some Bulgarian manufactured magazines. 

- Features a spring catch which will allow an easy attachment point to the spring. This prevents the block making noise and epoxy can be added at this point to make it permanent.

NOTE: These are made of additive manufacturing using high temperature ABS plastic. They're very durable and will last the life of the magazine. 

- If you are interested in identification of your AK magazines here is an excellent resource: AK47 Mag Identification

Smith & Wesson M&P .45 Magblock 10 Round Limiters

- Fits 14 round .45ACP M&P magazines. 
- New design installs at the base of the spring with the "L" shape of the spring going through the block.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W Magazines M&P .45acp

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*Universal Pistol Limiter Instructions: Cut to #16+hole and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  

Walther .40 P99 Magblock 10 Round Limiters

- Fits 14 round .40 Factory Walther PPX magazines as shown.
- Easy installation under the follower as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Walther P99 and PPQ Magblock 10 Round Limiters For 20 Round Magazine

- Fits 20 round 9mm Factory Walther P99 and PPQ magazines as shown.
- Easy installation under the follower as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Magblock for SKS Archangel Promag (7.62x39mm) Magazines.

- This block fits the Promag SKS Archangel 20 round magazines in 7.62x39mm and will convert them to a 10 or 15 round magazine. Select option below. 

- Replaces the lower locking plate for an easy and secure install.

.

 Magblock 10 Round Limiter for Heckler & Koch USP Expect 9mm

- Fits 16 round .40s&w H&K USP expert magazines. 
- Limits the magazinbe to 10 rounds of .40
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design. 

FYI: This block is made from our Universal Pistol Limiter and is cut so that the number "12" shows up in the indicator notch. The lock tab is not used and the slide is cut so that it is flush with the base of the limiter. The 2 pieces are then bonded together. See photos for details. 

 

FNP-9 Magblock 10 Round Limiter

- Fits 15 round 9 mm Factory FNP-9 magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Smith & Wesson 4006, 4046, 4043 Magblock 10 Round Limiters

- Fits 11 round .40 4006, 4046, 4043 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 4006 magazine.

 

Zev Technologies Plus 5 Glock 17 and Glock 34 (9mm) Magblock  10/22

- Fits 22 round 9mm Zev Technologies plus 5 basepad extension for Factory Glock 17 and Glock 34 magazines.  *See details on correct follower types below. 

- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures. 

Patent Pending

*This block is intended for the +5 Zev Technologies basepad extensions attached to a factory Glock 17 & Glock 34 magazine, and will limit a 22 round magazinedown to 10 rounds. *See pictures of Zev +5 Extension. 

ASC USGI 6.5 Grendel Magblock 10/25 MCL (Magazine Capacity Limiter)

- For use in ASC USGI 6.5 Grendel 25 round magazines. 
- These blocks will convert a 25 round magazine to hold only 10 rounds.

Magblock 10/30 limiter for KCI 5.56x45/.223 mm AR Magazines only.

- Tested and designed for KCI AR-15 magazines.
- These blocks will convert a 30 round 5.56x45 mm magazine to hold only 10 rounds.

Promag Colt 2000 Magblock 10 Round Limiter

This Magblock fits the Promag Colt 2000 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10 round Promag Colt 2000 Magazines.

-No external modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instructions: If using the Universal limiter to make this cut to #9 in the indicator notch and cement the base. Next the sides of the base will need to be sanded down to fit into the bottom of the magazine. The block sold here is pre cut and sanded. 

Magblock 10 Round Limiter for Sig P227 (.45) 14 Round Magazines

- Fits 14 round .45 Sig P227 magazines.  (13+2 extension)
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Magblock 10 Round Limiter for Tisas Zigana 15 Round Magazines

- Fits 15 round 9mm Tisas Zigana & PX-9 Carry factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #15 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #15 with the top part of #15 will show in the limiter window notch like in the photos.  

Arsenal Strike One Magblock 10 & 15 Round Limiters for 17 Round Magazine

- Fits 17 round 9mm Arsenal Strike One magazines as shown.
- Tested in Arsenal Strike One 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number "14" shown in the indicator notch. Cement together after testing fit. 

Mini 14 Magblock 5/30 MCL (Magazine Capacity Limiter for Ruger Magazines for Hunting

 This block is for use in RUGER 30 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 30 round magazine to hold only 5 rounds for hunting. 

- Only for use in RUGER manufactured magazines. 

- This is a modified USGI magblock.

Mini 14 Magblock 5/20 MCL (Magazine Capacity Limiter for Ruger Magazines for Hunting.

 This block is for use in RUGER 20 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 20 round magazine to hold only 5 rounds. 

- Only for use in RUGER manufactured magazines. 

- This is a modified USGI magblock.

CMMG AR-15 .22LR 10/25 Magblock 10 Round Limiter

- This block will convert 25 round CMMG AR-15 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

 -This block is for CMMG .22LR Evolution magazines in the pictures only. Will not work on USGI style magazines. That block is coming soon.

ProMag 1911  .45 Magblock

• Fits 15 round ProMag 1911 .45 magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of .45
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

Lancer L7 5/20 Limiter for 20 round magazines in .308/7.62x51mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 5 rounds for hunting.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear. 
Note: This is a custom modified Pmag block and will replace the original base. 

Beretta M9A3 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Beretta M9A3 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Beretta M9A3 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta M9A3 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #18 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #18 will show in the limiter window notch like in the photos. 

 

Lancer L7 5/10 Limiter for 10 round magazines in .308/7.62x51mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 10 round magazine to hold only 5 rounds for hunting.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear. 
Note: This is a custom modified Pmag block and will replace the original base. 

Magnum Research Baby Desert Eagle Fast Action Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Magnum Research Baby Eagle FA magazines as shown.
- Tested in Magnum Research Baby Eagle Fast Action 9mm 15 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 16 shown in the indicator notch. Cement together after testing fit. 

*This block is designed for the "Fast Action" Baby Desert Eagle magazine. 

Magnum Research Baby Desert Eagle Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Magnum Research Baby Eagle magazines as shown.
- Tested in Magnum Research Baby Eagle 9mm 15 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

CZ-75 CzechmateTactical Sport 10/26 Magblock 10 Round Limiter for 26 Round factory magazines

This Magblock fits the CZ-75 Czechmate Tactical Sport 26 round magazines will limit them to 10 rounds. Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/26 CZ-75 Czechmate Tactical Sport magazines.

- No external modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

 

CMMG USGI AR-15 .22LR 10/25 Magblock 10 Round Limiter

- This block will convert 25 round CMMG USGI AR-15 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines. Allows use of factory locking plate and base plate.

 -This block is for CMMG .22LR USGI magazines in the pictures only. Will not work in Clear CMMG .22LR magazines. 

Hudson H9 9mm Magblock 10 and 15 Round Limiters

- Fits 17 round 9mm Factory  Hudson H9 9mm magazines.
- Easy installation at the base of the magazine. 
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Note: This limiter can also be made using our Universal Pistol Limiter and cutting flush at the base with #20 showing in the indicaor notch. 
The limiters shown here come pre-cut and glued for a drop in conversion. 

Magblock for US Palm AK47 (7.62x39mm) Magazines.

- This block fits the US Palm 30 round AK47 magazines in 7.62x39mm and will convert them to a 10 round magazine.

Want to upgrade to the best stainless steel AK replacement springs available? See our upgrade springs here: LINK

Walther .40 PPQ M2 Magblock 10 Round Limiters

- Fits 13 round .40 Factory Walther PPQ M2 magazines as shown.
- Tested in M2 version PPQ Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal just cut flush at the base with number #12 shown in the indicator notch. Cement together after testing fit. 

Walther PDP Magblock 10 Round Limiters

- Fits 18 round 9mm Factory Walther PDP magazines as shown.
- Tested in Walther PDP Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

-This block will fit the new 18-round PDP Compact magazine.

-ATTENTION: Walther has recently changed their locking plate design. So you need to determine which size locking plate you have. An easy way to tell is the new magazines have the blue follower and thin locking plate.

SEE PICS for example. 

Magblock 10 Round Limiter for EAA Girsan MC28 15 Round Magazines

- Fits 15 round 9mm EAA Girsan MC28 factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #11.5 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #11 with the top part of #12 will show in the limiter window notch like in the photos.  

Magblock 10 Round Limiter for Bul Armory SASII 2011 170mm 28 Round 9mm Magazines

- Fits 28 round 9mm Factory Bul Armory SAS2 170 mm magazines. 
- Easy installation at the base of the magazine. (See pictures for details)
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

Magblock 10 and 15 Round Limiter for Rock Island Armory/Armscor A2 1911 Double Stack 16 Round 10mm/.40 Magazines

- Fits 16 round 10mm/.40 RIA A2 1911 Double Stack magazines. 
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 10mm/.40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10/30 limiter for 5.56x45/.223 mm AR Magazines only.

- Tested and designed for UTG AR-15 magazines.
- These blocks will convert a 30 round 5.56x45 mm magazine to hold only 10 rounds.

10 Round Limiter for MSAR STG 42 Round Waffle Polymer Magazines

Magblock 10/42 MCL (Magazine Capacity Limiter) for MSAR STG 42 round polymer magazines in .223/5.56mm.

- This block will replace the lower spring attachment point or locking plate and convert a 42 round magazine to hold only 10 rounds.

- Customized base of the Magblock includes one locking point.

- Does not affect reliability.

- No increase in spring pressure.

-Tested on MSAR STG 42 round magazine only. 

Taurus TX-22  (.22LR) Magblock 10 Round Limiter 

- Fits 15 round Taurus TX-22 magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

10 Round Limiter for MSAR STG 20 Round Waffle Polymer Magazines

Magblock 10/20 MCL (Magazine Capacity Limiter) for MSAR STG 20 round polymer magazines in .223/5.56mm.

- This block will replace the lower spring attachment point or locking plate and convert a 20 round magazine to hold only 10 rounds.

- Customized base of the Magblock includes one locking point.

- Does not affect reliability.

- No increase in spring pressure.

-Tested on MSAR STG 20 Round magazine only.

H&K AR-15 Polymer Magazine Magblock 10/30 Limiter

- For use in H&K MR556 and HK416 type 30 round polymer magazines as pictured.

- These blocks will convert a 30 round magazine to hold only 10 rounds.

*This block is desinged for the polymer magazine only. 

Magblock 10 Round Limiter for Sarsilmaz ST45 .45 magazines

- Fits 12 round .45 Sarsilmaz ST45 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Sarsilmaz ST45 .45 magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

 

Okay Industries Surefeed E2 Magblock 10/30 USGI MCL (Magazine Capacity Limiter) for AR15/M16 Magazines

- For use in Surefeed E2 USGI type 30 round magazines for the AR15/M16. 
- These blocks will convert a 30 round magazine to hold only 10 rounds.

 

This block will work with 32 round 9mm ProMag Cobray M-11 magazines to make a 10 round magazine.  The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.

Block installs at the base and allows you to use the factory locking plate. 

Magblock 10/50 MCL (Magazine Capacity Limiter) for X-Products X-15 HXP 50 round Drum in .223/5.56mm.

- Magazines can be loaded with the bolt closed.
- Does not affect reliability
- No increase in spring pressure
- Easy to install, see the video. 

 

Magblock for Zastava Polymer AK47 (7.62x39mm) Magazines.

- This block fits the Zastava 30 round AK47 magazines in 7.62x39mm and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

Want to upgrade to the best stainless steel AK replacement springs available? See our upgrade springs here: LINK

Beretta BM-59 5/20 Magblock .308win/7.62x51 (Hunting)

Fits Beretta BM-59 Magazines in .308/7.62x51mm 20 round magazines and will convert them to hold only 5 rounds for hunting.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

 

Beretta BM-59 15/20 Magblock 

Fits Beretta BM-59 Magazines in .308/7.62x51mm 20 round magazines and will convert them to hold only 15 rounds for Colorado.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

 

Beretta BM-59 10/20 Magblock 

Fits Beretta BM-59 Magazines in .308/7.62x51mm 20 round magazines and will convert them to hold only 10 rounds.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

 

Magblock for Arsenal Circle 10 AK47 10/40 (7.62x39mm) Magazines.

- This block fits the Arsenal Circle 10 (Plastic follower only) 40 round AK47 magazines in 7.62x39mm and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

.

Shield Arms Glock 43X and Glock 48 (9mm) Magblock

- Fits Shield Arms 20 round 9mm Glock 43x and Glock 48.
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Shield Arms Glock 43X and Glock 48 (9mm) Magblock

- Fits Shield Arms 15 round 9mm Glock 43x and Glock 48.
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Note: This block will work in Gen 1, Gen 2, and Gen 3 magazines.

Amend2 Glock 23 (.40) Magblock

- Fits 13 round .40 Amend2 Glock 23 magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

Amend2 Glock 22 (.40) Magblock

- Fits 15 round .40 Amend2 Glock 22 magazines.  
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of .40. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

Amend2 Glock 9mm Magblock for 34 Round (9mm) Magazines

- Fits 34 round 9mm Amend2 Glock 17 magazines.  *See details on correct follower types below. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Amend2 Glock Magazines.
Only compatable with the follower type and magazine base extension shown in the pictures. If yours is different then modifications may be needed.

This block will work with 32 round 9mm Cobray M-11 magazines to make a 10 round magazine.  The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.

Block installs at the base. 

Magblock 10 Round Limiter for CZ P-09 & P10 (.40) 15 Round Magazines

- Fits 15 round .40 CZ P-09 & P-10 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .40S&W. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Smith & Wesson SD40 VE .40 Magblock 10 Round Limiters

- Fits 15 round Promag .40 SD40 magazines. 
- New design installs at the base of the spring.
- Limits the magazine to 10 rounds of .40 cal. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with Promag S&W 15 Round Magazines. 
- Save time and money, easier than pinning a magazine. Easily Block Magazines. 

*Universal Pistol Limiter Instructions: Cut to #12 and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #12 will show in the limiter window notch like in the photos.  (Block purchased here already has this done).

This block is design for Promag S&W SD40 magazine only.

Taran Tactical +1 Extension for Sig Sauer P320 10/18 (9mm) Magblock

- Fits 17 round 9mm Sig P320 with the TTI (Taran Tactical Innovations) +1 Magazine Extension.  *See Pictures For Details
- Easy installation at the base of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

-This block is designed to work with the +1 TTI Extension for the Sig P320 Full-size 17-round magaiznes.

 

 

Magblock 10 Round Limiter for Sig Gen 2 MPX 9mm 20 Round Magazines

- Fits 20 round 9mm Sig MPX factory magazines.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-This block will ONLY work in the new Sig MPX 20-round magazine pictured below.
 

 

GSG Mauser M-15 .22LR 10/22 Magblock 10 and 15 Round Limiter

- This block will convert 22 round GSG Mauser M-15 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne.

Stoeger STR-9 Combat 9mm Magblock 10 Round Limiter for 20 Round Magazine

- Fits 20 round 9mm Stoeger STR-9 Combat magazines. 
- Easy installation under the follower and is held in place with spring tension.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Stoeger STR-9 Compact 9mm Magblock 10 Round Limiter for 13 Round Magazine

- Fits 13 round 9mm Stoeger STR-9C magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9 mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Walther .40 P99 Magblock 10 Round Limiters

- Fits 11 round .40 Factory Walther P99 magazines as shown.
- Easy installation under the follower as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

MecGar Tanfoglio Witness Magblock Round Limiter for 17 Round Magazines Chambered in .38 Super

This Magblock fits the Mecgar Tanfoglio Stock Master 9mm, 17 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Tanfoglio Witness Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

"Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "13" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

 

Magblock for the Duramag/C-Products 20 round AR-10 Magazines. Made of heat and impact resistant fiber reinforced polymer. Won't deform even in the most hostile environments. 

Promag Sig Sauer P226 Magblock 10 Round Limiter for 15 Round Magazines

This Magblock fits the Promag Sig P226 15 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- Simple install to make 10/15 Promag Sig Sauer P226 magazines. 
- No modification to the magazine is required.
-  Lightweight and will not interfere with magazine reliability.
- Tested on Promag Sig P226 magazines as shown in the photos. The block may need to be modified to work with magazines from other manufactures. 

Note: This block is designed for the Promag Sig P226 15-Round Magazines only.

Promag Taurus PT111 G2 Magblock 10/15 (9mm) 10 Round Limiter

This Magblock fits the Promag Taurus PT111 G2 15 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired or required. This provides an easy method to convert your Promag Taurus PT111 G2 magazines to 10 rounds. No external modification to the magazine is required

Has been tested on Promag magazines only.

 

SAR-9 Magblock 10 Round Limiter For 19 Round Magazine

- Fits 19 round 9mm Factory Sarsilmaz SAR-9 magazines as shown.
- Tested in SAR9 19 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 23 shown in the indicator notch. Cement together after testing fit. 

Magblock 10 Round Limiter for THRIL GEN 2 SM9 MPX 9mm 35 Round Magazines

- Fits 35 round 9mm MPX THRIL GEN 2 magazines.
- Easy installation by inserting the block at the base. This block replaces the factory locking plate.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

Magblock 10 Round Limiter for FN Reflex 15 Round Magazines

- Fits 15 round 9mm FN Reflex magazines.
- Easy installation under the follower.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.

 

Magblock 10 Round Limiter for Sig P226 20 Round Mec-Gar Magazines

This Magblock fits the Sig P226 X-Five Mec-Gar 20 round magazines (With aluminum addition as shown) made by Mec-Gar and will limit them to 10 rounds.

- Easy installation at the base of the spring.

- Limits the magazine to 10 rounds of 9mm.

- Held in place with spring tension or can be epoxied for a permanent modification.

- Lightweight, efficient design.

- Made of a super strong, heat resistant, fiber reinforced polymer.

Block used is a Universal Pistol Limiter cut to #22.

KCI Beretta 92FS Magblock 10/30 (9mm) 10 Round Limiter

This Magblock fits the KCI Beretta 92FS 30 round 9mm magazines and will limit them to 10 rounds.  Easily installed at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/30 KCI Beretta 92 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original KCI Beretta 92 magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

Magblock 10 Round Limiter for Kimber Mako R7 (9mm) 15 Round Magazines

- Fits 15 round 9mm magazines
- Easy installation under the follower.- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Tested on Kimber Mako R7 15 round magazine.

Magblock 10 Round Limiter for ETS CZ Scorpion Evo (9mm) 30 Round Magazines

- Fits 30 round 9mm ETS CZ Scorpion Evo magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

 *This block is designed for the ETS (Elite Tactical Systems) CZ 30 Round magazines only. It will not work in the CZ factory magazines. Look at the picture below to determine which magazine you have. We carry blocks for factory and aftermarket CZ style of magazines. 

 

Magblock 10 Round Limiter for Grand Power CP380 12 Round Magazines

- Fits 12 round .380 Factory Grand Power CP380 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .380. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

-Tested on factory Grand Power CP380 magazines.The block may need to be modified to work with magazines from other manufactures.

.* Universal limiter can be cut to #8 showing in the notch to make this limiter. 

Magblock 10 Round Limiter for Promag Browning Hi Power 13 Round Magazines

- Fits 13 round 9mm Promag Hi Power magazines.
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.

 Note: This block is designed for the Promag Browning Hi Power 13-round Magazine only

AREX Zero S1 Compact Magblock 10 Round Limiters 

- Fits 15 round 9mm Factory AREX Zero Compact S1 magazines as shown.
- Tested in AREX Zero S1 Compact 15 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 10 shown in the indicator notch. Cement together after testing fit. 

 

Promag PS-90, P-90 MAGBLOCK 10/50 MAGAZINE

- New and Improved Easy Install Design.

- This block will fit original 5.7x28mm Promag PS-90, P-90 Magazines made by Promag.

- The block replaces the factory locking plate and will convert 50 round magazines to hold only 10 rounds. 

- The block can be epoxied to the spring for a permanent modification.

*PATENT PENDING*

 

ASC USGI 6.8 SPC Magblock 10/25 MCL (Magazine Capacity Limiter)

- For use in ASC USGI 6.8 SPC 25 round magazines. 
- These blocks will convert a 25 round magazine to hold only 10 rounds.

MecGar (K40) Tanfoglio Witness 10 Round Magblock Round Limiter for 14 Round Magazines

This Magblock fits the Mecgar Tanfoglio Witness FT  .40, 14 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Tanfoglio Stock Master and  Italia Defiant Stock Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

"Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "9" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

 

Smith & Wesson M&P 22 Magnum Magblock 10 Round Limiters

- Fits 30 round .22 Magnum M&P magazines. 
- New design installs at the base of the magazine and is held in place with spring tension. You will use the factory locking plate.
- Limits the magazine to 10 rounds of 22 magnum. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W 30 Round M&P 22 Magnum Magazines. 

Taurus PT92 and PT99 Compact Magblock 10/12 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT92 and PT99 Compact 12 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/12 Compact Taurus PT92 and PT99 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT92/PT99 Compact magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Ruger American Compact 10/12 Magblock 10 Round Limiter for 12 Round Magazines

This Magblock fits the Ruger American Compact Pistol  9mm, 12 round magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Ruger American Pistol Magazines.
-No modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instuctions: To make this limiter from a universal cut the base flush with "3" showing in the indicator notch. Cement the base and slide together. Limiters ordered on this listing come Premade to these specifications. 

Beretta 80X Magblock 10/13 (.380) 10 Round Limiter

This Magblock fits the factory Beretta 80X 13 round .380 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/13 Beretta 80X magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta 80X magazines as shown in the photos. Other types of magazines may require modification of the limiter. 
*Please click on photos for installation instructions. 

If using the Universal Limiter: Cut the universal limiter to between numbers 4 to 5 showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done. 

ITAC Defense 10 Round Limiter Magblock 10/30

- For use in Itac Defense type 30 round magazines for the AR15. 
- These blocks will convert a 30 round magazine to hold only 10 rounds. 

 

Magnum Research Mountain Eagle  (.22LR) Magblock 10 Round Limiter 

- Fits 20 round .22 Mountain Eagle magazines. 
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22 
- Held in place with tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*Please click on photos for installation instructions. 

*This posting is for the Magblock (only) and not for the magazine. 

Taurus PT100 & PT101 Magblock 10/15 (.40) 10 Round Limiter

This Magblock fits the factory Taurus PT100 and PT101 15 round .40 magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Taurus PT100 & PT101 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT100 & PT101 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Taurus TH9 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus TH9 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Taurus TH9 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus TH9 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

 

Magblock 10 Round Limiter for Girsan MC P35 15 Round Magazines made by Mec Gar

- Only for use in the magazine type pictured.

- Fits 15 round 9mm Girsan MC P35 magazines by Mec Gar.
- Easy installation at the base of the magzine.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.
- Made using our Universal Pistol Limiters pre-cut and fixed at #15.

Gen M3 Magpul PMag 10/30 limiter 3 Pack Kit

Save time and money by making your magazines legal. 

- This Magblock fits the Gen3/M3 Magpul 30-round Pmags.

- Easily installs at the base of the spring. It is held in place with spring tension alone or can be epoxied if desired.

- No modification to the magazine is required.

- Lightweight and will not interfere with magazine reliability.

- Requires cutting of the Magblock for Gen3 20-round and 10-round magazines.

-Magazines can be loaded with the bolt closed.

 

 

Mecgar Smith & Wesson 5900 Series Magblock 10/17 (9mm)

This Magblock fits the Mecgar Smith & Wesson 5900 Series 17 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine, and It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/17 Mecgar S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

Mecgar Smith & Wesson 5900 Series Magblock 10/20 (9mm)

This Magblock fits the Mecgar Smith & Wesson 5900 Series 20 round 9mm magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the magazine, and It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10/20 Mecgar S&W 5900 Series magazines.

-No modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

Glock 32 (.357) Magblock

- Fits 13 round .357 Sig caliber Glock 32.  *See details on correct follower types below. 

- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of .357 Sig caliber ammunition. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatable with the follower type shown in the pictures.