Smith & Wesson M&P .45 Magblock 10 Round Limiters

- Fits 14 round .45ACP M&P magazines. 
- New design installs at the base of the spring with the "L" shape of the spring going through the block.
- Limits the magazine to 10 rounds of .45. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. - Tested with factory S&W Magazines M&P .45acp

*Please click on photos at left for installation instructions. New design installs at the base of the spring and sits on top of the original locking plate.

*Universal Pistol Limiter Instructions: Cut to #16+hole and glue flush at the bottom for 10/14 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #16 will show in the limiter window notch like in the photos.  

AREX Rex Delta Magblock 10 Round Limiters 

- Fits 17 round 9mm Factory AREX Rex Delta magazines as shown.
- Tested in AREX Rex Delta 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 18 shown in the indicator notch. Cement together after testing fit. 

GSG-15 .22LR 10/22 Magblock 10 and 15 Round Limiter

- This block will convert 22 round GSG-15 .22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.

-Installs at the base of the magazne.

Walther .40 PPQ M2 Magblock 10 Round Limiters

- Fits 13 round .40 Factory Walther PPQ M2 magazines as shown.
- Tested in M2 version PPQ Magazines.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal just cut flush at the base with number #12 shown in the indicator notch. Cement together after testing fit. 

Lancer L7 5/20 Limiter for 20 round magazines in .308/7.62x51mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 5 rounds for hunting.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear. 
Note: This is a custom modified Pmag block and will replace the original base. 

ProMag 1911  .45 Magblock

• Fits 15 round ProMag 1911 .45 magazines. 
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of .45
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

ASC USGI 6.5 Grendel Magblock 10/25 MCL (Magazine Capacity Limiter)

- For use in ASC USGI 6.5 Grendel 25 round magazines. 
- These blocks will convert a 25 round magazine to hold only 10 rounds.

Magblock 10/30 limiter for KCI 5.56x45/.223 mm AR Magazines only.

- Tested and designed for KCI AR-15 magazines.
- These blocks will convert a 30 round 5.56x45 mm magazine to hold only 10 rounds.

Promag Colt 2000 Magblock 10 Round Limiter

This Magblock fits the Promag Colt 2000 15 round magazines and will limit them to 10 rounds of 9mm  Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

-Simple install to make 10 round Promag Colt 2000 Magazines.

-No external modification to the magazine is required.

-Lightweight and will not interfere with magazine reliability.

Universal Limiter Instructions: If using the Universal limiter to make this cut to #9 in the indicator notch and cement the base. Next the sides of the base will need to be sanded down to fit into the bottom of the magazine. The block sold here is pre cut and sanded. 

Magblock 10 Round Limiter for Sig P227 (.45) 14 Round Magazines

- Fits 14 round .45 Sig P227 magazines.  (13+2 extension)
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of .45
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock 10 Round Limiter for Tisas Zigana 15 Round Magazines

- Fits 15 round 9mm Tisas Zigana & PX-9 Carry factory magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

*If using our Universal Limiter for this magazine: Cut to #15 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. #15 with the top part of #15 will show in the limiter window notch like in the photos.  

Arsenal Strike One Magblock 10 & 15 Round Limiters for 17 Round Magazine

- Fits 17 round 9mm Arsenal Strike One magazines as shown.
- Tested in Arsenal Strike One 17 round magazine.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number "14" shown in the indicator notch. Cement together after testing fit. 

Magblock for US Palm AK47 (7.62x39mm) Magazines.

- This block fits the US Palm 30 round AK47 magazines in 7.62x39mm and will convert them to a 10 round magazine.

Want to upgrade to the best stainless steel AK replacement springs available? See our upgrade springs here: LINK

Hudson H9 9mm Magblock 10 and 15 Round Limiters

- Fits 17 round 9mm Factory  Hudson H9 9mm magazines.
- Easy installation at the base of the magazine. 
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Note: This limiter can also be made using our Universal Pistol Limiter and cutting flush at the base with #20 showing in the indicaor notch. 
The limiters shown here come pre-cut and glued for a drop in conversion.