Magblocks

Beretta APX Magblock 10/18 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 18 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/18 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #20 and glue flush at the bottom for 10/17 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #20 will show in the limiter window notch like in the photos. 

 Wilson Combat EDC X9 Magblock 10 Round Limiters for 18 Round Magazine

- Fits 18 round 9mm Factory Wilson Combact EDC X9 magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

Magblock 10 Round Limiter for Remington 1911 R1 9mm magazines

- Fits 19 round 9mm Remington 1911R1 magazines. 
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

*** Tested on factory Remington 1911 R1 9mm double stack magazines which use a locking plate at the base. The block may need to be modified to work with magazines from other manufactures or sizes. If your magazines do not have a plastic locking plate that sits on top ot the floor plater then they will not work. 

Magblock 10 Round Limiter for STI Staccato 126mm 17 Round 9mm Magazines

- Fits 17 round 9mm Factory Staccato STI P, XC, XL 126 mm magazines. 
- Easy installation into the follower of the magazine.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Only fits the floor plates shown. May need sanding shorter if your magazines have a floorplate locking plate.

*Note: If you have a newer Staccato STI magazine that has G3 on the back of the magazine, then you will need to click G3 option below.

Magblock for SKS Archangel Promag (7.62x39mm) Magazines.

- This block fits the Promag SKS Archangel 20 round magazines in 7.62x39mm and will convert them to a 10 or 15 round magazine. Select option below. 

- Replaces the lower locking plate for an easy and secure install.

.

Walther P99 and PPQ Magblock 10 Round Limiters For 20 Round Magazine

- Fits 20 round 9mm Factory Walther P99 and PPQ magazines as shown.
- Easy installation under the follower as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Walther .40 P99 Magblock 10 Round Limiters

- Fits 14 round .40 Factory Walther PPX magazines as shown.
- Easy installation under the follower as shown.
- Limits the magazine to 10 rounds of .40
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

This block will work with 30 round 9mm Grand Power Stribog magazines to make a 10 round magazine. Block allows you to use the stock locking plate.

AK-74 Bulgarian Magblock for 5.45x39mm 30 round magazines

• This AK-74 block fits most 30 round Bulgarian 5.45x39 mm magazines and will convert them to hold only 10 rounds.
• The new design features a spring catch which will allow an easy attachment point to the spring.
• This prevents the block making noise and epoxy can be added at this point to make it permanent.
• This block will replace the original magazine locking plate.

Tanker AK47 10/20 Magblock

This block fits the Tanker 20 round AK47 magazines and will convert them to a 10 round magazine.

-Replaces the lower locking plate.

-Works on Korean surplus magazines.

Taurus PT24/7 Magblock 10/17 (9mm) 10 Round Limiter

This Magblock fits the factory Taurus PT24/7 17 round 9mm magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/17 Taurus PT24/7 magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Taurus PT24/7 magazines as shown in the photos. Other types of magazines may require modification of the limiter.

Please click on photos for installation instructions.

Beretta APX Magblock 10/15 (.40) 10 Round Limiter

This Magblock fits the factory Beretta APX 15 round .40 magazines and will limit them to 10 rounds.  Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired.

- Simple install to make 10/15 Beretta APX magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Beretta APX magazines as seen in the photos. Other types of magazines will likely require modification of the limiter. 

*Please click on photos for installation instructions. 

*Universal Limiter Instructions: Cut to #9 and glue flush at the bottom for 10/15 limiter. Slide lock is not used. When epoxy cures assemble magazine. The two parts of the universal limiter must be glued flush to prevent the locking plate from causing the limiter to shift sideways. #9 will show in the limiter window notch like in the photos. 

 Wilson Combat EDC X9S Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Wilson Combact EDC X9S magazines as shown.
- Easy installation at the base of the spring as shown.
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Universal Limiter Instructions:  To make this limiter out of the Universal  just cut flush at the base with number 15 shown in the indicator notch. Cement together after testing fit. 

Beretta ARX160 22LR 10/30 Magblock 10 Round Limiter

- This block will convert 30 round Beretta ARX160 22LR magazines into a 10 round magazine.

- Easy to install without damage to your magazines.