Products

Magblock for the LaRue Tactical 20 round AR-10 Magazines. Made of heat and impact resistant fiber reinforced polymer. Won't deform even in the most hostile environments. This is the same as the M14 Limiter. Will be a tight fit in the base. Thanks to EBR Works for this compatibility update. Check them out at for compliance work:  http://www.ebrwebstore.com/middleman-ffl-services

Magblock 10 Round Limiter for CZ P-07 Duty (9mm) 16 Round Magazines

- Fits 16 Round 9mm CZ P-07 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Patented Design 

*** Universal Pistol Limiter Instructions: Cut to "11" showing in the indicator notch and a flush base. (Ordering here is for pre-cut and finished blocks for a drop in limiter.)

H&K 417 Magblock 5/10 Limiter

- For use in H&K 417 - MR762  type 10 round magazines as pictured.

- These blocks will convert a 10 round magazine to hold only 5 rounds.

Magblock 5 Round Limiter for CZ Scorpion Evo (9mm) 20 Round Magazines

- Fits 20 round 9mm CZ Scorpion Evo magazines
- Easy installation at the base of the spring.
- Limits the magazine to 5 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock 15/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in 300 Blackout only.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 15 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.- Does not affect reliability.

- No increase in spring pressure. 

ASC - DURAMAG AR 7.62X39 10 & 15 ROUND LIMITER FOR 30 ROUND MAGAZINE

• New Design
• Converts the updated ASC AR-15 7.62x39 30 round magazine to 10 rounds.
• Easy installation 
• Does not affect reliability 

Magblock for Mossberg 590M 2 Round Limiter for 10 Round Magazines (12ga)

• Fits Mossberg 10 round magazines and will limit them to 2 rounds in the magazine for hunting. 
• Fits under the follower. The original plug will need to be removed by pulling out with pliers. See photos.
• Can be held in with included screw or epoxy if a permanent modification is needed. 

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in 300 Blackout only.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.- Does not affect reliability.

- No increase in spring pressure. 

MagBlock Branded PMAG Retaining Plate For Gen M2 & Gen M3

- MagazineBlocks LLC locking plate for Magpul PMAG .223/ 5.56 magazines.

Fits 10, 20, and 30 round Pmags. This is our brand locking plate and is a great options if we're sold out of the factory Magpul version.

Works the same. Choose Generation of your magazines below: Gen M3 will state this on the side. If you don’t see it then you have Gen 2 / /MOE pmags.

Magblock for Mossberg 590M 2 Round Limiter for 5 Round Magazines (12ga)

• Fits Mossberg 5 round magazines and will limit them to 2 rounds in the magazine for hunting. 
• Fits under the follower. The original plug will need to be removed by pulling out with pliers. See photos.
• Can be held in with included screw or epoxy if a permanent modification is needed. 

Lancer L7 10/20 Limiter for 20 round magazines in .308/7.62x51mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 10 rounds.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear. 
Note: This is a custom modified Pmag block and will replace the original base. 

Ruger Mini 30 Magblock 10/20 Magazine Capacity Limiter

 This block is for use in RUGER 20 round factory Mini 30 magazines. These blocks will insert at the base of the magazine spring and convert a 20 round magazine to hold only 10 rounds.

- Only for use in RUGER manufactured magazines. 

Great for the range bag and to show your magazines are blocked. 

Also for patch collectors like myself :)

- 3” Round PVC 

- Hook and loop backing 

Magblock Universal Pistol Base only