Products

Fits M14/M1A 7.62x51mm/.308 20 round magazines.

- Easiest and quickest way to make a 10 round M14 Magazine.

- Can be permanently attached to the spring with epoxy.

- The block attaches to the spring to prevent noise and movement.

- No magazine modifications required.

-Allows loading on a closed bolt with 10 rounds installed.

-New light weight design.

* Will work in new Springfield 20 Round M1A magazines. 

Converts AR-15 7.62x39 C-Products and ASC 30 round magazine to 10 rounds

Mag Magnet for AR15

ALL NEW and Improved Generation 2 model, using the N52 Neodymium Magnet for strongest hold with 1.3 lb more strength than the original. 
Mag Magnet is a patented product that is magnetized and used with the standard bullet button for California legal AR-15's. Mag Magnet is a true original, don't fall for cheap imitations.

For use with the standard AR-15 platform (.223/5.56mm).
Mag Magnet is not compatible with the Prince 50 or the Raddlock. It only works with the standard Bullet Button™.

Magblock LLC only recommends use of this device out of state or with .22 rimfire conversion kits only.

Leaving Mag-Magnet on a firearm may designate it as an illegal assault weapon in violation of California law. Do not use Mag-Magnet in California on magazines with capacities greater than 10 rounds. It is advised that Mag-Magnet users become familiar with California DOJ requirements and updated interpretations of existing laws and regulations.

Magblock LLC shall not be held responsible in any way for the inappropriate use of the product by the user. User assumes all liabilities and risks associated with ownership and use of this product.

Converts 9mm AR-15 32 round magazine to 10 rounds.

This block will work with 9mm AR-15 magazines. It was designed for the C-products and ASC magazines, but may work with other similar magazines. It replaces the lower floor plate. The spring can also be epoxied to the block which allows for disassembly. Can be cut down to fit other pistol caliber magazines. Will not fit UZI magazines but we do offer an UZI block. 

Converts FAL 20 round magazines to 10 rounds.

This block will fit surplus military FAL 20 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.

Converts C-Products 6.8mm 25 round magazines to 10 rounds.

Magblock 10/25 MCL block for use in C-Products, ASC, and other 6.8 mm 25 round magazines. This block will convert a 25 round magazine to hold only 10 rounds of 6.8mm. May fit other 25 round 6.8 mm magazines also

NOTE: This it a cut down USGI Magblock, so the top was milled off. Works perfectly.

Saiga 10/30 Magblock 

- Converts the Saiga .223 Surefire 30 round magazine to 10 rounds.

- This block fits the Saiga polymer 30 round magazines in .223/5.56mm.

- This block will replace the original magazine locking plate.

- Fits  Surefire (SGM) magazines. Others may need modification for a correct fit.

Colt USGI 10/20 MCL Magblock

For use in ONLY Colt 20 round magazines. (See USGI 10/20 for other types of USGI magazines.)

-This block will attach to the bottom of the spring and convert 20 round magazines to hold only 10 rounds.

-COLT  USGI magazines use a modified 10/20 USGI block which has been trimmed and an adapter plate plastic welded on.

-Requires no magazine modifications. 

Works on G3 and HK91 twenty round magazines.

G3 and HK91 10/20 Block for 7.62x51mm or .308 magazines.

To Install:
This new design is held to the spring by removing the locking plate and installing the spring into the hole in the block as seen in the photo. The block and spring is then inserted back into the magazine. The locking plate is then positioned under the block. Then slide the floor plate closed as normal.

No external modifications to the magazine are necessary.

- Fits Gen 2 Pmag 20 only (Straight body)

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in .223/5.56mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure. 

- Will also fit 30 round Emags. 

- Compatable with original Pmags and "M" Series only.  These will not work without modifications in Gen 3 or M3 Pmags. We will have another product set up to buy pre-trimmed M3 blocks. Here are instructions on how to trim blocks to work with Gen M3 Pmags:   http://www.calguns.net/calgunforum/showpost.php?p=9787410&postcount=261

SCAR 17 MAGBLOCK  

- New and Improved Easy Install Design.

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 10 rounds.

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

Made from super strong ABS plastic.

*PATENT PENDING*

 

Replacement 20 round Stainless Steel spring for use in Pmag and USGI magazines