Products

Magblock 5/30 For 5.56 & 300 Blackout (5 Round Magazine Capacity Limiter) 

This block is for use in Magpul 30 round Pmags. Both Gen 2 and M3. These blocks will replace the lower spring attachment point (locking plate) and convert a 30 round magazine to hold only 5 rounds where required for hunting. 

This block is desinged to work in the 300 Blackout (7.62x35) and the 5.56x45 - .223

You have to use both pieces of the block to work properly

Magblock for the LaRue Tactical 20 round AR-10 Magazines. Made of heat and impact resistant fiber reinforced polymer. Won't deform even in the most hostile environments. This is the same as the M14 Limiter. Will be a tight fit in the base. Thanks to EBR Works for this compatibility update. Check them out at for compliance work:  http://www.ebrwebstore.com/middleman-ffl-services

Magblock 10 Round Limiter for CZ P-07 Duty (9mm) 16 Round Magazines

- Fits 16 Round 9mm CZ P-07 magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Patented Design 

*** Universal Pistol Limiter Instructions: Cut to "11" showing in the indicator notch and a flush base. (Ordering here is for pre-cut and finished blocks for a drop in limiter.)

Magblock 5/10 MCL (5 Round Magazine Capacity Limiter) for Magpul 10 round Gen M3 Pmags in .223/5.56mm.

- Fits Gen M3 Pmag 10 Round Magazine
- This block will replace the lower spring attachment point or locking plate
- Will convert a 10 round magazine to hold only 5 rounds. Now offering a 1 round limiter for hunting in 350 Legend - 5.56.
- Does not affect reliability.
- No increase in spring pressure. 

*This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10 Round Magazine Capacity Limiter for Thermold 15 and 20 round AR-15/M16 Magazines.

- Will convert both a 20 or 15 round magazine to hold only 10 rounds.

- Only fits current production Thermold magazines. Has not been tested on older versions. Some modification may be needed for older production magazines. 
- The Thermold 15 and 20 round magazines use the same body size and differ only by a slight internal modification. The same limiter will limit both magazines to 10 rounds. 

Magblock 10/30 limiter for 5.45x39 mm AR Magazines only.

- Tested in C-Products and ACS magazines.
- These blocks will convert a 30 round 5.45x39 mm magazine to hold only 10 rounds.

Lancer L5 10/30 MCL (Magazine Capacity Limiter) for 30 round Lancer L5 Advanced WarFighter magazines in .223/5.56mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- Only fits L5 Advanced Warfighter with slide on base. Will not fit older L5 magazines.

- Does not affect reliability.

- No increase in spring pressure or wear. 

(Note: This is a custom modified Pmag block)

-This block will also work in the 30-round 300 Blackout Lancer magazines along with the new Gen 2 Warfighter magazines.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Magblock 10/20 MCL (Magazine Capacity Limiter) for Magpul 20 round Gen M3 Pmags in .223/5.56mm, 300 Blackout

- Fits NEW Gen M3 Pmag 20  (Curved body)

- This block will replace the lower spring attachment point  or locking plate and convert a 20 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed in most rifles. Some trimming of the limiter may be required for this.

- Does not affect reliability.

- No increase in spring pressure. 

- Attention: We now offer the option to use our block with the Magpul factory retaining plate with our block. The block will sit on top of the Magpul retaining plate and is cut differently than our standard Gen M3 10/30 magblock. If you're planning on not using the factory retaining plate then we have an options for you.

10 Round Limiter for Gen M3 30 Round Pmags

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Gen M3 Pmags in .223/5.56mm. 

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure. 

- This block will work in the New Magpul TMAG Gen M3 30-round magazines.

- Attention: We now offer the option to use our block with the Magpul factory retaining plate with our block. The block will sit on top of the Magpul retaining plate and is cut differently than our standard Gen M3 10/30 magblock. If you're planning on not using the factory retaining plate then we have an options for you.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.