Products

AR10 Magblock 10/20

Fits ACS and C-Products .308/7.62x51mm 20 round magazines and will convert them to hold only 10 rounds.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

- May fit other brand AR 10 Magazines. 

SCAR 17 MAGBLOCK

- New and Improved Easy Install Design.

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 15 rounds. 

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

- Can also limit a 10 round Scar 17 magazine to 5 rounds.

Made from super strong ABS plastic. 

*PATENT PENDING*

SCAR 17 MAGBLOCK 5/20

- New and Improved Easy Install Design.  Makes removal after hunting season easier. 

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 5 rounds.

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be secured to the spring for a permanent modification or removed to restore full 20 round capacity.

- For use where hunting laws restrict capacity to 5 rounds. 

Made from super strong ABS plastic.

*PATENT PENDING*

The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the current issue aluminum USGI 30-round magazine follower.

Featuring a patent pending 4-way anti-tilt design, the Enhanced Self-Leveling Follower is made from a non-hydroscopic and self-lubricating polymer.

Made in U.S.A.

The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the current issue aluminum USGI 30-round magazine follower.

Featuring a patent pending 4-way anti-tilt design, the Enhanced Self-Leveling Follower is made from a non-hydroscopic and self-lubricating polymer.

Made in U.S.A.

Developed from the operational experience of the Magpul DynamicsSM team, the B.A.D. Lever (Battery Assist Device) is designed to considerably improve the speed and efficiency of the AR15/M16 bolt catch.

The B.A.D. Lever quickly addresses reloading and malfunction clearance shortcomings of AR15/M16 platforms by extending a paddle to the right side of the weapon, allowing manipulation of the bolt stop from the fire control/ready position with the right-hand trigger finger.

Made from milspec-anodized aluminum, the B.A.D. Lever attaches to the standard AR15/M16 bolt release without permanent modification to the weapon.

Functional for both left and right-handed shooters, the B.A.D. Lever also allows traditional bolt catch manipulation according to the AR15/M16 manual of arms.

All mounting hardware included.

Made in U.S.A.

The Magpul PMAG Ranger Plate

This is a floorplate replacement for the 5.56x45 PMAG and EMAG that incorporates an integral loop similar to the original Magpul USGI Ranger.

When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.

Attention: These will only work on the Generation 1 and Generation 2 PMAGS. They will not work on Gen 3, due to their newer base design. 

The Magpul PMAG Ranger Plate

This is a floorplate replacement for the 5.56x45 PMAG and EMAG that incorporates an integral loop similar to the original Magpul USGI Ranger.

When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.

Attention: These will only work on the Generation 1 and Generation 2 PMAGS. They will not work on Gen 3, due to their newer base design. 

The Magpul PMAG Ranger Plate

This is a floorplate replacement for the 5.56x45 PMAG and EMAG that incorporates an integral loop similar to the original Magpul USGI Ranger.

When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.

Attention: These will only work on the Generation 1 and Generation 2 PMAGS. They will not work on Gen 3, due to their newer base design. 

Features:

- Stamped steel construction

- Military specification heavy phosphate coating

- Can be put on any standard AR-15 upper receiver

- Make a statement!

- "Frikken Laser" Engraved!

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round 6.8 mm "Six8" Pmags for LWRC.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- Includes a spacer for the proper height in the 6.8 mm magazine.

- Does not affect reliability.

- No increase in spring pressure. 

- *Compatible with Pmag 6.8 mm Magazines Only