Products

Magblock 10 Round Limiter for CZ P-09/P-09 F Nocturne (9mm) 19 Round Magazines

- Fits 19 round 9mm CZ P-09 Full-Size - P-09 F Nocturne magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 
- Made of a super strong, heat resistant, fiber reinforced polymer.

Magblock for VZ 58 (7.62x39mm) Magazines.

- This block fits the VZ.58 30 round magazines in 7.62x39mm and will convert them to a 10 round magazine.

- Replaces the lower locking plate for an easy and secure install.

- These are marked as an "AK47" limiter but is modified to work in the VZ.58. I know these rifles don't usually share any parts :)

-NOTE: Only fits the type of VZ.58 magazine shown in the photos. These will not work if your magazine internals are significantly different than those pictured.

AR10 Magblock 5/10

Fits ACS and C-Products .308/7.62x51mm 10 round magazines and will convert them to hold only 5 rounds.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

- May fit other brand AR 10 Magazines. 

SCAR 17 MAGBLOCK

- New and Improved Easy Install Design.

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 10 round magazines to hold only 5 rounds, or a 20 round magazine to hold 15 rounds 

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

- Can also limit a 20 round Scar 17 magazine to 15 rounds.

- Made from super strong ABS plastic. 

Same as this item:  http://www.magazineblocks.com/magento/products/magblock-kits/scar-17/scar-17-magblock-15-20.html

*PATENT PENDING*

ASC - DURAMAG AR 7.62X39 10 & 15 ROUND LIMITER FOR 30 ROUND MAGAZINE

• New Design
• Converts the updated ASC AR-15 7.62x39 30 round magazine to 10 rounds.
• Easy installation 
• Does not affect reliability 

Magblock for Mossberg 590M 2 Round Limiter for 10 Round Magazines (12ga)

• Fits Mossberg 10 round magazines and will limit them to 2 rounds in the magazine for hunting. 
• Fits under the follower. The original plug will need to be removed by pulling out with pliers. See photos.
• Can be held in with included screw or epoxy if a permanent modification is needed. 

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in 300 Blackout only.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.- Does not affect reliability.

- No increase in spring pressure. 

MagBlock Branded PMAG Retaining Plate For Gen M2 & Gen M3

- MagazineBlocks LLC locking plate for Magpul PMAG .223/ 5.56 magazines.

Fits 10, 20, and 30 round Pmags. This is our brand locking plate and is a great options if we're sold out of the factory Magpul version.

Works the same. Choose Generation of your magazines below: Gen M3 will state this on the side. If you don’t see it then you have Gen 2 / /MOE pmags.

Magblock for Mossberg 590M 2 Round Limiter for 5 Round Magazines (12ga)

• Fits Mossberg 5 round magazines and will limit them to 2 rounds in the magazine for hunting. 
• Fits under the follower. The original plug will need to be removed by pulling out with pliers. See photos.
• Can be held in with included screw or epoxy if a permanent modification is needed.