Products
-
Mini 14 MCL 10/20 Block (Promag)
Mini 14 Magblock 10/20 MCL (Magazine Capacity Limiter)
This block is for use in PROMAG 20 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 20 round magazine to hold only 10 rounds.
- Only for use in PROMAG magazines at this time.
- The bottom of the follower may need slight trimming to load on a closed bolt with 10 rounds loaded in the magazine. See the photos for details.
- This is a modified USGI magblock.
$6.95 As low as: $5.95 -
Magpul Enhanced Self-leveling Follower USGI .223 - FOL GRN
The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the current issue aluminum USGI 30-round magazine follower.
Featuring a patent pending 4-way anti-tilt design, the Enhanced Self-Leveling Follower is made from a non-hydroscopic and self-lubricating polymer.
Made in U.S.A.
$2.09 -
Magpul Enhanced Self-leveling Follower USGI .223 - Yellow
The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the current issue aluminum USGI 30-round magazine follower.
Featuring a patent pending 4-way anti-tilt design, the Enhanced Self-Leveling Follower is made from a non-hydroscopic and self-lubricating polymer.
Made in U.S.A.
$2.09 -
B.A.D. LEVER - Battery Assist Device (BAD)
Developed from the operational experience of the Magpul DynamicsSM team, the B.A.D. Lever (Battery Assist Device) is designed to considerably improve the speed and efficiency of the AR15/M16 bolt catch.
The B.A.D. Lever quickly addresses reloading and malfunction clearance shortcomings of AR15/M16 platforms by extending a paddle to the right side of the weapon, allowing manipulation of the bolt stop from the fire control/ready position with the right-hand trigger finger.
Made from milspec-anodized aluminum, the B.A.D. Lever attaches to the standard AR15/M16 bolt release without permanent modification to the weapon.
Functional for both left and right-handed shooters, the B.A.D. Lever also allows traditional bolt catch manipulation according to the AR15/M16 manual of arms.
All mounting hardware included.
Made in U.S.A.
$29.95 -
Pmag Ranger Plate .223 Foliage
The Magpul PMAG Ranger Plate
This is a floorplate replacement for the 5.56x45 PMAG and EMAG that incorporates an integral loop similar to the original Magpul USGI Ranger.
When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.
Attention: These will only work on the Generation 1 and Generation 2 PMAGS. They will not work on Gen 3, due to their newer base design.
$7.95 -
Pmag Ranger Plate .223 FDE
The Magpul PMAG Ranger Plate
This is a floorplate replacement for the 5.56x45 PMAG and EMAG that incorporates an integral loop similar to the original Magpul USGI Ranger.
When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.
Attention: These will only work on the Generation 1 and Generation 2 PMAGS. They will not work on Gen 3, due to their newer base design.
$7.95 -
SCAR 17 Magblock 10/20
SCAR 17 MAGBLOCK
- New and Improved Easy Install Design.
- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.
- The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 10 rounds.
- No modifications to your expensive FN SCAR magazines are needed to install.
- The block can be epoxied to the spring for a permanent modification.
Made from super strong ABS plastic.
*PATENT PENDING*
$10.95 As low as: $8.95 -
H&K Polymer MR556, HK416 10/30 Magblock (.556)
H&K AR-15 Polymer Magazine Magblock 10/30 Limiter
- For use in H&K MR556 and HK416 type 30 round polymer magazines as pictured.
- These blocks will convert a 30 round magazine to hold only 10 rounds.
*This block is desinged for the polymer magazine only.
$6.95 As low as: $5.95 -
Magblock Upgrade 30 Round AK-47 Replacement Spring for Polymer Magazines
- Replacement upgrade stainless steel springs.
- Uses highest quality 17-7 Stainless Steel to prevent tension loss.
- Fits all Polymer AK-47 magazines including Pmag, Tapco, Promag, Circle10, Bakelite, Arsenal, etc.
- Exceeds military specs
- Guaranteed not to lose tension!
- Great to use with Magblock Limiters also.
- Order our 24 coil for use in mil spec metal AK mags.
Replacement upgrade 30 round spring for use in AK magazines including Pmags, Tapco, Promag, Circle10, Bakelite, Arsenal. Use along with our 10 round blocks for an upgrade or save your original springs. Uses the highest quality 17-7 Stainless spring steel which has the best properties for magazine spring use. Most companies don't use this quality steel due to the added cost, but if you want the best it will cost a little more. These 30rd AK47 magazine spring holds up in the harshest condition and won't loose tension over time even if maintained fully loaded. We guarantee spring will not be damaged from long term storage of fully loaded magazines!
These springs use 17-7 PH is a precipitation-hardened stainless steel that is well suited for aerospace and other applications requiring high strength and good corrosion resistance and formability. Type 17-7PH is a Chromium-Nickel-Aluminum, austenitic stainless steel. It is the most formable of all PH grades and has the highest strength and hardness. It is less magnetic than other PH grades and offers minimal distortion upon heat treatment. This material maintains its valuable properties at temperatures up to 800 F.
$6.99 -
CZ Scorpion Evo PGS Hybrid Magblock 10/32 (9mm)
Magblock 10 Round Limiter for CZ Scorpion Evo PGS Hybrid (9mm) 32 Round Magazines
- Fits 32 round 9mm CZ Scorpion Evo PGS Hybrid magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.
$6.95 As low as: $5.95 -
CZ Scorpion Evo 3 Plus Magblock 10/20 (9mm)
Magblock 10 Round Limiter for CZ Scorpion Evo 3+ (9mm) 20 Round Magazines
- Fits 20 round 9mm CZ Scorpion Evo Window and Blackedout version 3+ magazines
- Easy installation at the base of the spring.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.
- Made of a super strong, heat resistant, fiber reinforced polymer.* This block is designed for the CZ factory Window and 3 Plus Blackout 20 Round magazines only. It will not work in the CZ Smoke Gray magazines. Look at the picture below to determine which magazine you have. We carry blocks for both styles of magazines.
CZ Evo Factory Smoke Gray 10/20 Magblock: https://www.magazineblocks.com/magento/cz-scorpion-magblock-10-20-9mm.html
$6.95 As low as: $5.95 -
Kel-Tec P17/P17 Compact Magblock 10/16 (.22)
Kel-Tec P17 (.22) 10/16 Magblock 10 or 15 Round Limiter
- This block will convert 16 round Kel-Tec P17 (.22) magazines into a 10 or 15 round magazine.
- Easy to install without damage to your magazines.
*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.
$6.59 As low as: $5.95 -
Mission First Tactical 10/30 Magblock
Magblock 10/30 MCL (Magazine Capacity Limiter) for Mission First Tactical 30 round Magazine in .223/5.56mm.
- Magazines can be loaded with the bolt closed.
- Does not affect reliability.
- No increase in spring pressure.
- Will work on Standard Mission First Tactical, Mod 2, and Extreme Duty mags.
-The stock locking plate is to be used with this Magblock.
$6.59 As low as: $5.95 -
CETME 10/20 Magblock (.308)
CETME 10/20 Magblock
Fits CETME Military Surplus Magazines in .308/7.62x51mm 20 round magazines and will convert them to hold only 10 rounds.
- No need to drill any holes.
- Load magazines on a closed bolt.
- Easy to install.
- No external magazine modifications.
- May fit other brand AR 10 Magazines.
$6.95 As low as: $5.95 -
GSG .22LR 10/22 Magblock (.22LR)
GSG-16, GSG-5, 522 .22LR 10/22 Magblock 10 Round Limiter
- This block will convert 22 round GSG .22LR magazines into a 10 round magazine.
- Easy to install without damage to your magazines.
-Installs at the base of the magazne.
*This posting is for the magblock (only) and not for the magazine. We don't currently sell any magazines at all.
$6.49 As low as: $5.95
