Products

Works on G3 and HK91 twenty round magazines.

G3 and HK91 10/20 Block for 7.62x51mm or .308 magazines.

To Install:
This new design is held to the spring by removing the locking plate and installing the spring into the hole in the block as seen in the photo. The block and spring is then inserted back into the magazine. The locking plate is then positioned under the block. Then slide the floor plate closed as normal.

No external modifications to the magazine are necessary.

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

- Fits Gen 2 Pmag 20 only (Straight body)

Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in .223/5.56mm.

- This block will replace the lower spring attachment point  or locking plate and convert a 30 round magazine to hold only 10 rounds.

- The Pmag dust covers will still fit when loaded.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure. 

- Will also fit 30 round Emags. 

- Compatable with original Pmags and "M" Series only.  These will not work without modifications in Gen 3 or M3 Pmags. We will have another product set up to buy pre-trimmed M3 blocks. Here are instructions on how to trim blocks to work with Gen M3 Pmags:   http://www.calguns.net/calgunforum/showpost.php?p=9787410&postcount=261

10 Block Bulk Pack

• 10 block bulk pack. Includes ONLY the following: Pmag M2/MOE 10/30, Pmag M2/MOE 10/20, USGI 10/30, and USGI 10/20, HK G36, XD/XDm 9 and .40 Pistol blocks, and Glock 9 and .40 Pistol blocks, excluding the Glock 10/33. 
• You MUST specify the quantity and type of each block below. Please be specific. 

Excludes 10/20 Colt blocks and Gen 3 blocks

Features:

- Stamped steel construction

- Military specification heavy phosphate coating

- Can be put on any standard AR-15 upper receiver

- Make a statement!

- "Frikken Laser" Engraved!

The Magpul PMAG Ranger Plate

This is a floorplate replacement for the 5.56x45 PMAG and EMAG that incorporates an integral loop similar to the original Magpul USGI Ranger.

When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.

Attention: These will only work on the Generation 1 and Generation 2 PMAGS. They will not work on Gen 3, due to their newer base design. 

• Converts 9mm AR-15 32 round magazine to 10 rounds.
• This block will work with 9mm AR-15 magazines made by ProMag only.
• It replaces the lower floor plate. 
• The spring can also be epoxied to the block which allows for disassembly and cleaning. 
• We have a separate block available for UZI, C-Products, and ASC 32 round magazines. This one only fits Promag magazines.

Arsenal Bulgarian Circle 10 AK-47 Magblock

-This block fits the Arsenal 30 round AK47 magazines and will convert them to a 10 round magazine

-This block will also work on the smoothside Bulgarian 30-round AK-47 magazines pictured

-Replaces the lower locking plate

-Works on Arsenal Bulgarian 7.62x39mm AK magazines

Note: This block is made from our Universal AK Kits cut to #38 using a square locking plate

*ATTENTION: This posting is for the Magblock (only) and not for the magazine. We don't currently sell any magazines at all.

Springfield XD 9mm Magblock

• Fits 16 round XD and XD Mod 2 9mm magazines.
• Easy installation under the magazine follower.
• Limits the magazine to 10 rounds of 9mm.
• Held in place with spring tension or can be epoxied for a permanent modification. 
• Lightweight, efficient design. 

Heckler & Koch G36 Magblock

- Works with Magpul Pmag Magazines for the HK G36 only.

- 10/30 configuration (10 rounds in a 30 round body)

- Replaces the original locking plate

- Simple quick install. 

Tapco Intrafuse AR-15 Magblock

- Magblock 10/30 MCL block for use in polymer Tapco Intrafuse AR-15 magazines.

- This block will convert a 30 round magazine to hold only 10 rounds. 

- The block replaces the lower Tapco locking plate.

NOTE: The Tapco follower must be modified like in the picture to hold all 10 rounds. 

AR10 Magblock 10/20

Fits ACS and C-Products .308/7.62x51mm 20 round magazines and will convert them to hold only 10 rounds.

 - No need to drill any holes. 

 - Load magazines on a closed bolt.

 - Easy to install. 

- No external magazine modifications. 

- May fit other brand AR 10 Magazines. 

SCAR 17 MAGBLOCK

- New and Improved Easy Install Design.

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 15 rounds. 

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be epoxied to the spring for a permanent modification.

- Can also limit a 10 round Scar 17 magazine to 5 rounds.

Made from super strong ABS plastic. 

*PATENT PENDING*

SCAR 17 MAGBLOCK 5/20

- New and Improved Easy Install Design.  Makes removal after hunting season easier. 

- This block will fit original 7.62x51mm NATO/.308 SCAR 17 Magazines made by FNH.

- The block attaches to the bottom of the magazine spring and will convert 20 round magazines to hold only 5 rounds.

- No modifications to your expensive FN SCAR magazines are needed to install.

- The block can be secured to the spring for a permanent modification or removed to restore full 20 round capacity.

- For use where hunting laws restrict capacity to 5 rounds. 

Made from super strong ABS plastic.

*PATENT PENDING*