Products
-
H&K HK416, MR556, SA80 Magblock 10/30 (5.56)
H&K Magblock 10/30 Limiter
- For use in H&K SA80 and HK416 type 30 round magazines as pictured.
- These blocks will convert a 30 round magazine to hold only 10 rounds.
- The locking plate is not used with the limiter installed.
$6.50 As low as: $5.95 -
PMAG LWRC Six8 Magblock (6.8mm)
Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round 6.8 mm "Six8" Pmags for LWRC.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Includes a spacer for the proper height in the 6.8 mm magazine.
- Does not affect reliability.
- No increase in spring pressure.
- *Compatible with Pmag 6.8 mm Magazines Only
$6.95 As low as: $5.25 -
FAL 10/30 Magblock
Converts FAL 30 round magazines to 10 rounds.
This block will fit FAL 30 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.Tested in DSARMS manufactured 30 round magazines, but should work in other similar magazines.
$6.59 As low as: $4.95 -
S&W M&P15 .22 Magblock (.22LR)
M&P15 .22LR 10/25 Magblock 10 Round Limiter
- This block will convert 25 round M&P15 .22LR magazines into a 10 round magazine.
- Easy to install without damage to your magazines.
- Replaces the original locking plate.
$6.95 As low as: $5.95 -
VEPR .308 Magblock 5, 10, and 15 Round Limiters
Magblock for Vepr .308 20 Round Magazines. 5, 10 and 15 Round Limiters.
Fits Vepr .308/7.62x51mm 20 round magazines made by Csspecs>
- Easy to install in seconds.
- Tested in Vepr magazines made by Csspecs. May fit other manufacturers with or without modification.
- Replaces the original locking plate.
- No external magazine modifications.
- Select 5, 10 or 15 round limiter below.$6.95 As low as: $5.95 -
PMAG GEN M3 LR/SR-25 Magblock 10/20 (.308)
Pmag LR20 Magblock GEN M3 Magazine Capacity Limiters (5, 10, and 15 Round Limiters Available)
Fits the Magpul LR20 .308/7.62x51mm Pmags and will convert them to hold only 5, 10, or 15 rounds. Select desired size below. Easy to install.
- Will NOT fit older version magazines. Gen M3 Only.
- Dust covers still fit with 10 rounds loaded.
- Load magazines on a closed bolt in most rifles.
- Easy to install.
- No external magazine modifications.
-This block requires you use the factory Magpul locking plate with our block (See picture 1 and 2).
$6.59 As low as: $5.95 -
CAA 15/30 Magblock 15 Round Limiter
15 Round Limiter for CAA Indicative 30 Round Polymer Magazines
Magblock 15/30 MCL (Magazine Capacity Limiter) for CAA 30 round polymer magazines in .223/5.56mm.
- This block will attach to the bottom of the spring, and sits on top of the original locking plate.
- Easy conversion of 30 round CAA magazines to hold 15 rounds.
- Does not affect reliability.
- No increase in spring pressure.$6.25 As low as: $5.25 -
AR-10 ArmaLite Magblock 10/20 (.308)
Magblock for ArmaLite AR10 20 Round Magazines. 10 and 15 Round Limiters.
Fits ArmaLite AR10 .308/7.62x51mm 20 round magazines and will convert them to hold either 10 or 15 rounds.
- Easy to install in seconds.
- No need to drill any holes.
- Load magazines on a closed bolt in most rifles.
- No external magazine modifications required.New lighter, more reliable design is made from abs plastic.
$6.95 As low as: $5.95 -
Steyr AUG 10/30 Magblock (5.56)
10 Round Limiter for Steyr AUG 30 Round Polymer Magazines
Magblock 10/30 MCL (Magazine Capacity Limiter) for Steyr AUG 30 round polymer magazines in .223/5.56mm.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Customized base of the Magblock includes two locking points just like the original locking plate.
- Does not affect reliability.
- No increase in spring pressure.
$7.49 As low as: $6.69 -
Pmag Ranger Plate .223 Black- Gen M3
For use with Magpul Pmag Gen M3Gen M3 Magpul PMAG Ranger Plate
This is a floorplate replacement for the 5.56x45 PMAG Gen M3 that incorporates an integral loop similar to the original Magpul USGI Ranger.
When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and control during high stress, tactical magazine changes.
Fits Gen M3 Pmags only in 10, 20, and 30 round sizes.
$7.95 -
SCAR 16 Magblock 10/30
SCAR 16 Magblock 10/30
- For use in the SCAR 16 FNH 30 round magazines
- These blocks will convert a 30 round SCAR 16 magazine to hold only 10 rounds.
- No modification to your original SCAR magazines is required to use these limiters.
- NOTE: For use only in FNH manufactured SCAR 16 factory magazines. For regular metal AR magazines you must use the USGI limiters.
$6.95 As low as: $5.95 -
Masterpiece Arms MPA 10/32 Magblock 9mm (Tapco)
10 Round Limiter for 32 Round Tapco MPA Magazines
Magblock 10/32 Magazine Capacity Limiter for the Masterpiece Arms 32 round 9mm magazines made by Tapco.
- This block will replace the lower spring attachment point or locking plate and convert a 32 round magazine to hold only 10 rounds.
- Very easy to install
- Does not affect reliability.
- No increase in spring pressure.
- Slight modification of the follower is required to fit all 10 rounds. Please see the pictures posted here for instructions.
$6.95 As low as: $5.95 -
H&K416 22LR 10/30 Magblock
HK416 22LR 10/30 Magblock 10 Round Limiter
- This block will convert 30 round HK 416 22LR magazines into a 10 round magazine.
- Easy to install without damage to your magazines.
$6.95 As low as: $5.49 -
Ruger Mini 14 Magblock 10/20 (.223/300Blk)
Mini 14 Magblock 10/20 MCL (Magazine Capacity Limiter for Ruger Magazines
This block is for use in RUGER 20 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 20 round magazine to hold only 10 or 15 rounds. (Select option below).
- Only for use in RUGER manufactured magazines.
- This is a modified USGI magblock.
- This block will work in both the 5.56/223 and 300 Blackout Ruger Mini 14 magazine.
$6.95 As low as: $5.95 -
Gen 2 Pmag 15/30 Magblock (GEN 2)
Magblock 15/30 MCL (Magazine Capacity Limiter) for Magpul 30 round Pmags in .223/5.56mm. (Gen 2)
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 15 rounds.
- Magazines can be loaded with the bolt closed.
- Does not affect reliability.
- No increase in spring pressure.
- Will also fit 30 round Emags.
Note: This is a trimmed down 10 round block to allow 15 rounds. These will not work in Gen M3 Pmags. Gen M3 Pmag 15 round limiters are available as a different product. These fit Gen 2 Pmags only.
$6.59 As low as: $4.95
