Developed from the operational experience of the Magpul DynamicsSM team, the B.A.D. Lever (Battery Assist Device) is designed to considerably improve the speed and efficiency of the AR15/M16 bolt catch.

The B.A.D. Lever quickly addresses reloading and malfunction clearance shortcomings of AR15/M16 platforms by extending a paddle to the right side of the weapon, allowing manipulation of the bolt stop from the fire control/ready position with the right-hand trigger finger.

Made from milspec-anodized aluminum, the B.A.D. Lever attaches to the standard AR15/M16 bolt release without permanent modification to the weapon.

Functional for both left and right-handed shooters, the B.A.D. Lever also allows traditional bolt catch manipulation according to the AR15/M16 manual of arms.

All mounting hardware included.

Made in U.S.A.

MAGBLOCK UNIVERSAL AK LIMITER KIT

ALLOWS FOR AN EASY CUSTOM SOLUTION FOR MOST METAL AK TYPE MAGAZINES. REQUIRES CUTTING OF THE MAGBLOCK FOR A CUSTOM FIT. AS SHIPPED IT WILL LIMIT MOST 30 ROUND MAGAZINES TO SLIGHTLY LESS THAN 10 ROUNDS.

Fits most steel 30 round AK47, AK74, AKS, SKS, VZ, and Saiga magazines and will convert them to hold only 10 or 15  rounds. Replaces the flat locking plates at the bottom of the spring. This part must be removed. Tested with Romanian, Russian, Korean, Promag, Saiga, IO, Chinese magazines and more.

- Features a spring catch which will allow an easy attachment point to the spring. This prevents the block making noise and epoxy can be added at this point to make it permanent.
- Pre notched cut outs in the most common lengths for easy cutting.
- Works on many military spec steel AK47 magazines.

Don't forget to check out our new upgrade stainless steel AK springs for polymer and steel magazines here or add below to your order. 

Epoxy Fast Setting

Hardman Double Bubble Pouch (4.0 grams). Will work for a few rifle or up to 5-10 pistol limiters depending on amount used.
Features:
- Starts to set in only 3- 5 minutes. Mix small batches if doing a lot of limiters.
- Handling strength: 15-30 minutes.
- Color: white.
- Viscosity: honey.
- Full Strength: 24 hours

4.0 Grams.

Epoxy, Machinable Fast Setting.

Hardman Double Bubble Pouch (3.5 grams). Will work for a few rifle or up to 10 pistol limiters depending on amount used.
Features a longer working time than the Red fast set epoxy:
- Starts to set in 25 minutes, Handling time 4 hours. Mix small batches if doing a lot of limiters.
- Handling strength: 4 hours.
- Color: Aluminum.
- Viscosity: Honey.
- Full Strength: 24 hours

3.5 Grams.

Features:

- Stamped steel construction

- Military specification heavy phosphate coating

- Can be put on any standard AR-15 upper receiver

- Make a statement!

- "Frikken Laser" Engraved!

Springfield Hellcat 9mm 10/11 Magblock

- Fits 11 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Magblock for the Duramag/C-Products 20 round AR-10 Magazines. Made of heat and impact resistant fiber reinforced polymer. Won't deform even in the most hostile environments. 

Daniel H9 9mm Magblock 10 Round Limiters

- Fits 15 round 9mm Factory Daniel Defense H9 9mm magazines.
- Easy installation at the base of the magazine. 
- Limits the magazine to 10 rounds of 9mm
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.

Note: This limiter can also be made using our Universal Pistol Limiter and cutting flush at the base with #12 showing in the indicaor notch. 
The limiters shown here come pre-cut and glued for a drop in conversion. 

Springfield Hellcat Pro 9mm 10/17 Magblock

- Fits 17 round 9mm Hellcat Pro magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

 

Springfield Hellcat 9mm 10/15 Magblock

- Fits 15 round 9mm Hellcat Compact  magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

 

Note: Please verify which number is showing under the follower of your magazine. If the number reads #4 or #3 then you'll need a special cut Hellcat block. If it reads any other number, then you can use the standard cut block.

• New Design
• Converts the updated DURAMAG AR-15 7.62x39 20 round magazine to 10 rounds.
• Easy installation 
• Does not affect reliability 

Springfield XDM Elite 9mm Magblock

- Fits 20 round 9mm XDM magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Springfield XDM Elite 9mm Magblock

Springfield XDM Elite 9mm Magblock

- Fits 22 round 9mm XDM magazines. 
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm. 
- Held in place with spring tension or can be epoxied for a permanent modification. 
- Lightweight, efficient design. 

Springfield XDM Elite 9mm Magblock

Magblock 10/32 MCL (Magazine Capacity Limiter) for Daniel Defense 32 round magazines in .223/5.56mm.

- Magazines can be loaded with the bolt closed.

- Does not affect reliability.

- No increase in spring pressure.