Search results for '5%2F30'
-
5.45x39 AR15 Magblock 10/30 Limiter
Magblock 10/30 limiter for 5.45x39 mm AR Magazines only.
- Tested in C-Products and ACS magazines.
- These blocks will convert a 30 round 5.45x39 mm magazine to hold only 10 rounds.
$5.95 As low as: $4.50 -
Gen 5 Glock Factory Floor Plate 9mm,40,357
Gen 5 Glock Factory Floor Plate (Fits 9mm, .40, .357)
- Replacement Glock factory floor plate for 9mm, .40 and .357 magazines.
$5.95 -
Zev +5 Extension Glock 17, 34 Magblock 10/22 (10 Round Limiter)
Zev Technologies Plus 5 Glock 17 and Glock 34 (9mm) Magblock 10/22
- Fits 22 round 9mm Zev Technologies plus 5 basepad extension for Factory Glock 17 and Glock 34 magazines. *See details on correct follower types below.
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures.Patent Pending
*This block is intended for the +5 Zev Technologies basepad extensions attached to a factory Glock 17 & Glock 34 magazine, and will limit a 22 round magazinedown to 10 rounds. *See pictures of Zev +5 Extension.
$6.95 As low as: $5.95 -
HEXMAG .223 /5.56mm AR15 10/20 Magblock
New Hexmag AR-15 Magblock 10/20 Magblock
- Magblock 10/20 MCL block for use in polymer Hexmag AR-15 magazines.
- This block will convert a 20 round magazine to hold only 10 rounds.
- Uses the original Hexmag locking plates.
$6.50 As low as: $5.95 -
Lancer L5 5/20 Magblock 300 Blackout/350 Legend
Lancer L5 5/20 MCL (Magazine Capacity Limiter) for 20 round Advanced Warfighter L5 magazines in 300 Blackout & 350 Legend
- This new design block will sit on top of the lower spring attachment point or locking plate and convert a 20 round magazine to hold only 5 rounds.—
- Only fits L5 Advanced Warfighter with slide on base.
- Does not affect reliability.
- No increase in spring pressure or wear.
- Uses a custom modified Pmag Block.
$6.59 As low as: $5.95 -
Browning BAR 5/20 Magblock for (Hunting)
Fits Browning BAR .30-06 20 round magazines.
- Easiest and quickest way to make a 5 round Browning BAR Magazine perfect for hunting.
- Can be permanently attached to the spring with epoxy.
- The block attaches to the spring to prevent noise and movement.
- No magazine modifications required.
-Allows loading on a closed bolt with 10 rounds installed.
-New light weight design.
$9.95 As low as: $7.95 -
Lancer L7 5/10 Magblock (.308)
Lancer L7 5/10 Limiter for 10 round magazines in .308/7.62x51mm.
- This block will replace the lower spring attachment point or locking plate and convert a 10 round magazine to hold only 5 rounds for hunting.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear.
Note: This is a custom modified Pmag block and will replace the original base.$6.50 As low as: $5.75 -
Lancer L7 5/20 Magblock (Hunting) (.308)
Lancer L7 5/20 Limiter for 20 round magazines in .308/7.62x51mm.
- This block will replace the lower spring attachment point or locking plate and convert a 20 round magazine to hold only 5 rounds for hunting.
- Only fits L7 Advanced Warfighter with slide on base as shown.
- Does not affect reliability.
- No increase in spring pressure or wear.
Note: This is a custom modified Pmag block and will replace the original base.$6.95 As low as: $5.95 -
ASC 6.5 Grendel 10/25 Limiter
ASC USGI 6.5 Grendel Magblock 10/25 MCL (Magazine Capacity Limiter)
- For use in ASC USGI 6.5 Grendel 25 round magazines.
- These blocks will convert a 25 round magazine to hold only 10 rounds.$5.95 As low as: $5.49 -
ASC 6.5 Grendel 5/25 Magblock (5 Round Limiter Hunting)
ASC 6.5 Grendel USGI Magblock 5/25 (5 Round Magazine Capacity Limiter)
- Fits USGI 25 round magazines made by ASC 6.5 Grendel.
- This block will attach to the bottom of the spring.
- Will convert a 25 round (6.5 Grendel) magazine to hold only 5 rounds for hunting.
- Magazines can be loaded with the bolt closed in most rifles. Fitting may be required in some cases.
- Does not affect reliability.
- No increase in spring pressure.
-Installs at the base of the magazine.$6.95 As low as: $5.95 -
PMAG AK47 5/30 Round Limiter (Hunting)
Magblock 5 Round Limiter for Magpul 30 Round AK-47 Pmag (7.62x39mm)
This block fits the new Magpul 30 round AK47 magazines and will convert them to hold 5 rounds for Hunting.
- Replaces the lower locking plate for an easy and secure install.
- Built in spring catch holds the limiter securely in place and prevents noise.
- Patented design not available anywhere else.*Made using out new Universal AK Limiter. If using the universal AK kit to make this limiter, cut so #39 shows in the indicator notch and use the Pmag lock insert. Along with an adapter.
$10.95 As low as: $8.95 -
Amend2 6.5 Grendel Magblock 5/10 Limiter (Hunting)
Amend2 6.5 Grendel Magblock 5/10 Limiter
- For use in Amend2 6.5 Grendel 10 round magazines as pictured.
- These blocks will convert a 10 round magazine to hold only 5 rounds.
$6.95 As low as: $5.95 -
M1_Carbine 5/15 Magblock (5 Round Limiter)
This easy to install 5 round magblock will limit a standard 15 round M1 carbine magazine. It simply slides onto the top of the spring right under the follower. Marked on the block for correct installation. No external modifications are needed. this block will limit the magazine capacity to 5 rounds, but still allow normal magazine function and bolt operation.$6.50 As low as: $5.95 -
HEXMAG .223 /5.56mm AR15 10/30 Magblock
Hexmag AR-15 Magblock 10/30
- Magblock 10/30 MCL block for use in polymer Hexmag AR-15 magazines.
- This block will convert a 30 round magazine to hold only 10 rounds.
- Uses the original Hexmag locking plates.
$6.50 As low as: $5.95 -
Tapco AR .223 /5.56mm 10/30 Block
Tapco Intrafuse AR-15 Magblock
- Magblock 10/30 MCL block for use in polymer Tapco Intrafuse AR-15 magazines.
- This block will convert a 30 round magazine to hold only 10 rounds.
- The block replaces the lower Tapco locking plate.
NOTE: The Tapco follower must be modified like in the picture to hold all 10 rounds.
$6.59 As low as: $5.49