Search results for '10%2F22 round limiter'
-
Browning BDA .380 Magblock 10 Round Limiter 10/13 (.380)
Browning BDA Magblock 10/13 (.380) 10 Round Limiter
This Magblock fits the factory Browning BDA and Beretta 84 13 round .380 magazines and will limit them to 10 rounds. Easily installed in seconds at the base of the spring. The factory locking plate is installed under the block. It is held in place with spring tension alone or can be glued or epoxied if desired. This provides an easy method to convert your factory Browning BDA .380 magazines to 10 rounds. No external modification to the magazine is required.
- Simple install to make 10/13 Browning BDA magazines.
- No modification to the magazine is required.
- Lightweight and will not interfere with magazine reliability.
- Works on original factory Browning BDA and Beretta 84 magazines as shown in the photos. Other types of magazines will likely require modification of the limiter.
*Please click on photos for installation instructions.If using the Universal Limiter: Cut the universal limiter to between numbers 4 to 5 showing in the indicator notch. Glue flush with the base. The front and back of the base will need to be sanded to better fit into the magazine. *The limiter sold here comes with all of this done.
$6.59 As low as: $5.95 -
MSAR 10/30 Magblock 10 Round Limiter
10 Round Limiter for MSAR 30 Round Polymer Magazines
Magblock 10/30 MCL (Magazine Capacity Limiter) for MSAR 30 round polymer magazines in .223/5.56mm.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Customized base of the Magblock includes one locking point.
- Does not affect reliability.
- No increase in spring pressure.
$6.59 As low as: $5.95 -
STEN 10/32 Magblock 10 Round Limiter
Magblock 10 Round Limiter for Sten 32 and 20 Round Magazines
- Fits Sten 32 round magazines and 32 round magazines that have been "Brass Wire" limited to 20 rounds. You must choose an option below.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Please Note: The Photos show a 32 round magazine that has 2 brass wires on the inside that protrude outside near the bottom of the magazine. This is a Sten 32 round magazines that was limited to a single stack 20 round magazine. This was a common military modification that helped with reliability and very widespread on surplus magazines. Please select the "Single Stack Modified" option below if you see these brass wires at the bottom of your magazine to ensure you receive the proper limiter. Thank you.$6.95 As low as: $5.95 -
CAA 10/30 Magblock 10 Round Limiter
10 Round Limiter for CAA Indicative 30 Round Polymer Magazines
Magblock 10/30 MCL (Magazine Capacity Limiter) for CAA 30 round polymer magazines in .223/5.56mm.
- This block will attach to the bottom of the spring, and sits on top of the original locking plate.
- Easy conversion of 30 round CAA magazines to hold 10 rounds.
- Does not affect reliability.
- No increase in spring pressure.$5.95 As low as: $5.25 -
Ruger Mini 14 Magblock 5/10 Round Limiters (Hunting)
Mini 14 Magblock 5/10 MCL (Magazine Capacity Limiter for Ruger Magazines for Hunting.
This block is for use in RUGER 10 round Mini 14 magazines. These blocks will attach to the lower spring and convert a 10 round magazine to hold only 5 rounds.
- Only for use in RUGER manufactured magazines.
$6.95 As low as: $5.95 -
Ruger Mini 30 Magblock 5/10 Round Limiter (Hunting)
Ruger Mini 30 Magblock 5/10 Magazine Capacity Limiter
This block is for use in RUGER 10 round factory Mini 30 magazines. These blocks will insert at the base of the magazine spring and convert a 10 round magazine to hold only 5 rounds for hunting.
- Only for use in RUGER manufactured magazines.
$6.95 As low as: $5.95 -
H&K P30 VP9 Magblock 10 Round Limiter for +5 Extension
Magblock 10 Round Limiter for Heckler & Koch P30 and VP9 9mm 15 round magazine that has a +5 HK store extension
- Fits 15 round to 20 round 9mm H&K P30 and VP9 magazines that has the +5 extension.
- Limits the magazine to 10 rounds of 9 mm
- Easy installation on top of the locking plate as shown in the photos.
- New, Improved design.
- Lightweight, efficient design.$6.59 As low as: $5.95 -
American Tactical Schmeisser S60 Magblock 10 Round Limiter (10/60)
American Tactical Schmeisser S60 10/60 Magazine block Limiter
- This block will replace the lower spring attachment point or locking plate and convert a 60 round magazine to hold only 10 rounds.
- Magazines can be loaded with the bolt closed.
- Does not affect reliability.
- No increase in spring pressure.
Disclaimer Warning: The spring in this magazine is under a lot of pressure. When dissambling the magazine to insert the block, keep it pointed in a safe direction. Away from your face and eyes.
$12.95 As low as: $12.50 -
SWAMP FOX 10/30 Magblock 10 Round Limiter
10 Round Limiter for SWAMP FOX 30 Round Polymer Magazines
Magblock 10/30 MCL (Magazine Capacity Limiter) for Swamp Fox 30 round polymer magazines in .223/5.56mm. The Swamp Fox TMG-M30-P01 is a 30 round light weight polymer magazine that fits 5.56×45 NATO and .223 Remington AR15/M16 style firearms.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Customized base of the Magblock includes a locking point just like the original locking plate.
- Does not affect reliability.
- No increase in spring pressure.
- Easy to install.$5.95 As low as: $5.25 -
ProMag Colt 2000 Magblock 10/15 (10 Round Limiter)
Promag Colt 2000 Magblock 10 Round Limiter
This Magblock fits the Promag Colt 2000 15 round magazines and will limit them to 10 rounds of 9mm Easily installed in seconds at the base of the magazine. It is held in place with spring tension alone or can be glued or epoxied if desired.
-Simple install to make 10 round Promag Colt 2000 Magazines.
-No external modification to the magazine is required.
-Lightweight and will not interfere with magazine reliability.
Universal Limiter Instructions: If using the Universal limiter to make this cut to #9 in the indicator notch and cement the base. Next the sides of the base will need to be sanded down to fit into the bottom of the magazine. The block sold here is pre cut and sanded.
$6.59 As low as: $5.95 -
USGI 350 Legend 10/20 Magblock (10 Round Limiter)
USGI 350 Legend Magblock 10/20 (10 Round Magazine Capacity Limiter)
- Fits USGI 20 round magazines made by C-Products/Duramag.
- This block will attach to the bottom of the spring.
- Will convert a 20 round (350 Legend) magazine to hold only 10 rounds.
- Magazines can be loaded with the bolt closed in most rifles. Fitting may be required in some cases.
- Does not affect reliability.
- No increase in spring pressure.
-Installs at the base of the magazine.$6.25 As low as: $5.75 -
E-Lander Elander 10/30 Magblock 10 Round Limiter
E-Lander Magblock 10/30 Magazine Capacity Limiter (10 Round Limiter)
- For use in E-Lander 30 round magazines.
- These blocks will convert a 30 round E-Lander magazine to hold only 10 rounds.
- Replaces the E-Lander locking plate and has a built in floor plate lock.- These can be used with USGI Ranger Plates and L-Plates. The bottom of the limiter can be modified for this and the block shortened by 2mm to allow room for the Magpul locking plate. We offer this as an option. You can also do it yourself following the instuctions found in the FAQ section here: http://www.magazineblocks.com/magento/faq FYI: Once the block is modified for use with a Ranger Plate or L-Plate the block can not be used without one of these products in place ot it will hold >10 rounds.
$5.95 As low as: $4.50 -
Promag COL-A18 AR 10/30 Magblock 10 Round Limiter
10 Round Limiter for Promag COL-A18 - AR15 30 Round Polymer Magazines
Magblock 10/30 MCL (Magazine Capacity Limiter) for Promag 30 round polymer magazines in .223/5.56mm. Model COL-A18.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Customized base of the Magblock includes two locking points just like the original locking plate.
- Does not affect reliability.
- No increase in spring pressure.
- Compatable with Promag model: COL-A18 - AR-15 / M16 .223-5.56x45mm (30)Rd Black Polymer Magazines only. These magazines have 2 small posts on the locking plate that lock into the floor plate.
$6.50 As low as: $5.95 -
Pmag 6.8 mm Six8 10/30 Magblock 10 Round Limiter
Magblock 10/30 MCL (Magazine Capacity Limiter) for Magpul 30 round 6.8 mm "Six8" Pmags for LWRC.
- This block will replace the lower spring attachment point or locking plate and convert a 30 round magazine to hold only 10 rounds.
- Includes a spacer for the proper height in the 6.8 mm magazine.
- Does not affect reliability.
- No increase in spring pressure.
- *Compatible with Pmag 6.8 mm Magazines Only
$6.95 As low as: $5.25 -
Zev +5 Extension Glock 17, 34 Magblock 10/22 (10 Round Limiter)
Zev Technologies Plus 5 Glock 17 and Glock 34 (9mm) Magblock 10/22
- Fits 22 round 9mm Zev Technologies plus 5 basepad extension for Factory Glock 17 and Glock 34 magazines. *See details on correct follower types below.
- Easy installation under the magazine follower.
- Limits the magazine to 10 rounds of 9mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.* Please click the photos for installation instructions. Fits newer generation full metal lined Glock Magazines.
Only compatible with the follower type shown in the pictures.Patent Pending
*This block is intended for the +5 Zev Technologies basepad extensions attached to a factory Glock 17 & Glock 34 magazine, and will limit a 22 round magazinedown to 10 rounds. *See pictures of Zev +5 Extension.
$6.95 As low as: $5.95