Search results for 'uzi'
-
UZI and MetalForm 10/25 Magblock
This block will work with 25 round 9mm UZI and Metalform magazines to make a 10 round magazine. It replaces the floor plate locking tab. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.$7.49 As low as: $6.49 -
UZI and Metalform 30/32 Magblock
This block will work with 32 round 9 mm UZI and MetalForm magazines to make a 30 round magazine. It replaces the lower floor plate. The spring can also be epoxied to the block which allows for disassembly and cleaning, or epoxy the floor plate closed for a more secure modification.$6.95 As low as: $5.95 -
UZI and MetalForm 10/32 Magblock
This block will work with 32 round 9mm UZI and Metalform magazines to make a 10 round magazine. It replaces the lower floor plate. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.$7.49 As low as: $6.49 -
Walther UZI Magblock (.22LR)
Walther UZI (.22LR) Magblock 10 Round Limiter
- Fits 20 round Walther UZI .22 magazines.
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.$6.59 As low as: $5.95 -
Colt, UZI and MetalForm 10/32 Magblock
This block will work with 32 round 9mm Colt, UZI and Metalform magazines to make a 10 round magazine. It replaces the lower floor plate. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.$7.49 As low as: $6.49 -
TEC-9 10/32 Magblock 9mm
10 Round Limiter for 32 Round TEC-9 Magazines
Magblock 10/32 Magazine Capacity Limiter for the TEC-9 32 round 9mm magazines pictured here.
- This block sits on top of the locking plate to convert a 32 round magazine to hold only 10 rounds.
- Very easy to install
- Does not affect reliability.
- No increase in spring pressure.
- Block is marked "STEN" with "2X" at the end.
$6.95 As low as: $5.95 -
Thompson .45 Magblock 10/30 Round Limiter
This block fits 30 Round Thompson .45 magazines to limit them to 10 rounds.The spring can also be epoxied to the block for a permanent installation. A spring catch at the bottom makes installation quick and easy.
$6.95 As low as: $5.95 -
Thompson .45 10/20 Round Limiter Magblock
This block fits 20 Round Thompson .45 magazines to limit them to 10 rounds.
The spring can also be epoxied to the block for a permanent installation. A spring catch at the bottom makes installation quick and easy.
$6.95 As low as: $5.95 -
STEN 10/32 Magblock 10 Round Limiter
Magblock 10 Round Limiter for Sten 32 and 20 Round Magazines
- Fits Sten 32 round magazines and 32 round magazines that have been "Brass Wire" limited to 20 rounds. You must choose an option below.
- Easy installation at the base of the spring.- Limits the magazine to 10 rounds of 9 mm.
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design. - Made of a super strong, heat resistant, fiber reinforced polymer. - Please Note: The Photos show a 32 round magazine that has 2 brass wires on the inside that protrude outside near the bottom of the magazine. This is a Sten 32 round magazines that was limited to a single stack 20 round magazine. This was a common military modification that helped with reliability and very widespread on surplus magazines. Please select the "Single Stack Modified" option below if you see these brass wires at the bottom of your magazine to ensure you receive the proper limiter. Thank you.$6.95 As low as: $5.95 -
Cobray M-11 Zytel 10/32 Magblock (9mm)
This block will work with 32 round 9mm Cobray M-11 magazines to make a 10 round magazine. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.
Block installs at the base.
$6.95 As low as: $5.95 -
Cobray M-10 Zytel 10/32 Magblock (9mm)
This block will work with 32 round 9mm Cobray M-10 magazines to make a 10 round magazine. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.
Block installs at the base.
$6.95 As low as: $5.95 -
ProMag Cobray M-11 Magblock Limiter 10/32
This block will work with 32 round 9mm ProMag Cobray M-11 magazines to make a 10 round magazine. The spring can also be epoxied to the block which allows for dis-assembly and cleaning, or epoxy the floor plate closed for a more secure modification.
Block installs at the base and allows you to use the factory locking plate.
$6.95 As low as: $5.95 -
Masterpiece Arms MPA 10/32 Magblock 9mm (Tapco)
10 Round Limiter for 32 Round Tapco MPA Magazines
Magblock 10/32 Magazine Capacity Limiter for the Masterpiece Arms 32 round 9mm magazines made by Tapco.
- This block will replace the lower spring attachment point or locking plate and convert a 32 round magazine to hold only 10 rounds.
- Very easy to install
- Does not affect reliability.
- No increase in spring pressure.
- Slight modification of the follower is required to fit all 10 rounds. Please see the pictures posted here for instructions.
$6.95 As low as: $5.95
