Search results for 'magnet'
-
Glock Follower .40
Glock Follower (.40) Replaces #10, Fit 6789, 079
Replacement Glock .40 follower which is compatible with our Magblocks.
-Replaces #10 and will work with Gen 2,3 and 4 magazines also.
$4.95 -
Magblock Epoxy Cement
Magblock Cement
Magblock Cement (15 ml bottle with applicator tip). Will work for a few rifle or up to 15+ pistol limiters depending on amount used. Features:
- Starts to set in only 1-3 minutes. Can be built up.
- Handling strength: 5 minutes.
- Color: Black.
- Viscosity: paste.
- Full Strength: 12 hours 15 ml bottle$3.95 -
HFT Super Glue
HFT Super Glue
A cyanoacrylate glue such as "super glue" is best for sealing the floor plate of Pmags closed. Pmags are made of Zytel polymer which is difficult to adhere to. Super glue on the base of the floorplate works well for a permanent modification.
3 grams
$1.95 -
Epoxy Fast Setting
Epoxy Fast Setting
Hardman Double Bubble Pouch (4.0 grams). Will work for a few rifle or up to 5-10 pistol limiters depending on amount used. Features:
- Starts to set in only 3- 5 minutes. Mix small batches if doing a lot of limiters.
- Handling strength: 15-30 minutes.
- Color: white.
- Viscosity: honey.
- Full Strength: 24 hours 4.0 Grams.$3.95 As low as: $3.79 -
M14 -M1A Blocks
Fits M14/M1A 7.62x51mm/.308 20 round magazines.
- Easiest and quickest way to make a 10 round M14 Magazine.
- Can be permanently attached to the spring with epoxy.
- The block attaches to the spring to prevent noise and movement.
- No magazine modifications required.
-Allows loading on a closed bolt with 10 rounds installed.
-New light weight design.
* Will work in new Springfield 20 Round M1A magazines.
$6.50 As low as: $5.95 -
Glock Follower 9mm
Glock Follower (9mm) Replaces #4,5,6, & Gen 4
Replacement Glock 9 mm follower which is compatible with our Magblocks.
-Replaces #4,5,6, and Gen 2,3 and 4 magazine followers in 9 mm.
$4.95 -
Suomi 10/36 Magblock
Limits 36 round Suomi magazines to 10 rounds.
New design does not replace the difficult to remove lower floor plate but instead rests on top of it.
The spring can also be epoxied to the block which allows for disassembly and cleaning.
Easy and simple way to make 10/36 Suomi magazines without damaging your hard to find magazine.
$6.25 As low as: $4.75 -
Magblock Universal Pistol Shaft
Magblock Universal Pistol Shalf only
$6.25 As low as: $5.49 -
Magpul Ranger Plate 223
The Magpul PMAG Ranger Plate is a floorplate replacement for the 5.56x45 PMAG and EMAG.
The ranger plate incorporates an integral loop similar to the original Magpul USGI Ranger.
When installed on the base of a magazine, the PMAG Ranger Plate provides unsurpassed speed and controllability during high stress, tactical magazine changes.
Made in U.S.A.
$5.95 -
Walther UZI Magblock (.22LR)
Walther UZI (.22LR) Magblock 10 Round Limiter
- Fits 20 round Walther UZI .22 magazines.
- Easy installation by replacing the locking plate. See photos.
- Limits the magazine to 10 rounds of .22
- Held in place with spring tension or can be epoxied for a permanent modification.
- Lightweight, efficient design.$6.59 As low as: $5.95 -
Patch MagazineBlocks.com Round
Great for the range bag and to show your magazines are blocked.
Also for patch collectors like myself :)
- 3” Round PVC
- Hook and loop backing
$4.95 -
Magblock Universal Pistol Base
Magblock Universal Pistol Base only
$6.25 As low as: $5.49 -
Glock .45 Follower G21
Glock .45 OEM Replacement Follower
Replacement Glock .45 follower which is compatible with Magblock Limiters
- Fits Glock 21 and other .45 Glock Magazines.
$4.95 -
Epoxy Machinable- Fast Set
Epoxy, Machinable Fast Setting.
Hardman Double Bubble Pouch (3.5 grams). Will work for a few rifle or up to 10 pistol limiters depending on amount used. Features a longer working time than the Red fast set epoxy:
- Starts to set in 25 minutes, Handling time 4 hours. Mix small batches if doing a lot of limiters.
- Handling strength: 4 hours.
- Color: Aluminum.
- Viscosity: Honey.
- Full Strength: 24 hours 3.5 Grams.$4.09 As low as: $3.89 -
FAL 10/30 Magblock
Converts FAL 30 round magazines to 10 rounds.
This block will fit FAL 30 round magazines and convert them to 10 rounds.
The end of the magazine spring will snap into the hole in the block to hold it in place.Tested in DSARMS manufactured 30 round magazines, but should work in other similar magazines.
$6.59 As low as: $4.95